Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and magnet. The sensor plate rotates and as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine rpm. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No. DTC Detection Condition Trouble Area
P0335 No crankshaft position sensor signal to ECM at engine speed of 600 rpm or more
(1 trip detection logic)
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Sensor plate (crankshaft)

·

ECM


P0339 In conditions (a), (b) and (c), when no crankshaft position sensor signal to ECM for 0.05 seconds or more.
(a) Engine revolution 1,000 rpm or more
(b) Starter signal is OFF
(c) 3 seconds or more have elapsed after starter signal was switched from ON to OFF
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Sensor plate (crankshaft)

·

ECM



Reference: Inspection using an oscilloscope.

A430117E02
2.781,0.573 3.177,0.76 0.396,0.188 10 false GND 2.76,1.375 3.125,1.563 0.365,0.188 10 false GND 0.281,0.573 0.5,0.729 0.219,0.156 10 false G2 0.281,1.385 0.51,1.531 0.229,0.146 10 false NE 1.281,1.875 2.104,2.052 0.823,0.177 10 false 20 ms./DIV. 2.656,0.094 3.26,0.292 0.604,0.198 10 false 5 V/DIV.

HINT:
·

G2 stands for the camshaft position sensor signal and NE stands for the crankshaft position sensor signal.

·

Grounding failure of the shielded wire may cause noise in the waveforms.



Tester Connection Tool Setting Condition Specified Condition
B73-27 (NE+) - B73-34 (NE-) 5 V/DIV, 20 ms./DIV Idling The correct waveform is as shown
B73-26 (G2) - B73-34 (NE-) 5 V/DIV, 20 ms./DIV Idling The correct waveform is as shown

MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor even though the engine is running, the ECM interprets this as a malfunction of the sensor.

This monitor runs for 10 seconds (the first 10 seconds of engine idle) after the engine is started.

WIRING DIAGRAM

A401744E01
0.979,1.26 1.323,1.448 0.344,0.188 10 false B71 0.969,1.417 2.708,1.604 1.74,0.188 10 false Camshaft Position Sensor 0.948,3.49 1.292,3.677 0.344,0.188 10 false B70 0.948,3.656 2.688,3.844 1.74,0.188 10 false Crankshaft Position Sensor 2.156,0.479 2.427,0.656 0.271,0.177 10 false G2 2.156,0.917 2.385,1.094 0.229,0.177 10 false G- 2.063,2.365 2.385,2.542 0.323,0.177 10 false NE- 2.115,3.01 2.396,3.188 0.281,0.177 10 false NE 2.031,3.25 2.396,3.427 0.365,0.177 10 false GND 2.469,0.25 2.625,0.438 0.156,0.188 10 false 1 2.469,0.896 2.625,1.083 0.156,0.188 10 false 2 2.448,2.135 2.604,2.323 0.156,0.188 10 false 2 2.448,2.771 2.604,2.958 0.156,0.188 10 false 1 2.448,3.125 2.604,3.313 0.156,0.188 10 false 3 2.896,2.052 3.052,2.24 0.156,0.188 10 false * 3.583,0.156 3.74,0.344 0.156,0.188 10 false * 5.865,0.25 6.135,0.427 0.271,0.177 10 false G2 5.865,0.896 6.188,1.083 0.323,0.188 10 false NE- 5.875,2.771 6.198,2.958 0.323,0.188 10 false NE+ 5.885,3.875 6.135,4.073 0.25,0.198 10 false E1 5.594,3.76 5.74,3.958 0.146,0.198 10 false 3 5.563,2.781 5.802,2.979 0.24,0.198 10 false 27 5.583,0.906 5.823,1.104 0.24,0.198 10 false 34 5.583,0.25 5.823,0.448 0.24,0.198 10 false 26 0.573,4.979 2.313,5.167 1.74,0.188 10 false *: Shielded 6.125,4.833 6.469,5.021 0.344,0.188 10 false B73 6.115,5.01 6.583,5.208 0.469,0.198 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found in the diagnostic troubleshooting procedure of DTC P0335, troubleshoot the engine mechanical systems.

·

Read the value on the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Start the engine and turn the GTS ON.

(c)

Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.


·

The engine speed can be confirmed in the Data List using the GTS. If there are no NE signals from the crankshaft position sensor despite the engine running, the engine speed will be indicated as 0. If the voltage output of the crankshaft position sensor is insufficient, the engine speed will be indicated as lower than the actual engine rpm.

·

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
a.

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance of the wire harness side connectors.

Standard Resistance:
Tester Connection Condition Specified Condition
B70-1(NE) - B73-27 (NE+) Always Below 1 Ω
B70-2 (NE-) - B73-34 (NE-) Always Below 1 Ω
B70-1(NE) or B73-27 (NE+) - Body ground Always 10 kΩ or higher
B70-2 (NE-) or B73-34 (NE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT CRANKSHAFT POSITION SENSOR (INSTALLATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT CRANKSHAFT POSITION SENSOR (INSTALLATION)
a.
A385403E05
0.49,1.781 0.802,1.979 0.313,0.198 10 false OK 2.646,1.781 2.958,1.979 0.313,0.198 10 false NG

Check the crankshaft position sensor installation.

OK:

Sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 2 CRANKSHAFT TIMING SPROCKET (TEETH OF SENSOR PLATE)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

4.INSPECT NO. 2 CRANKSHAFT TIMING SPROCKET (TEETH OF SENSOR PLATE)
a.

Check the teeth of the sensor plate.

OK:

Sensor plate does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

NG

REPLACE NO.2 CRANKSHAFT TIMING SPROCKET