Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

w/ ABS:

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU (brake actuator assembly) and speed sensor. The speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A430791E01
0.26,1.094 1.5,1.458 1.24,0.365 10 false From Wheel Speed Sensor 1.813,1.99 3.229,2.156 1.417,0.167 10 false Skid Control ECU 3.719,1.99 5.135,2.156 1.417,0.167 10 false Combination Meter 3.115,0.625 3.927,0.802 0.813,0.177 10 false 4-Pulse 5.042,0.625 5.854,0.802 0.813,0.177 10 false 4-Pulse 6.042,1.354 6.49,1.521 0.448,0.167 10 false ECM

w/o ABS:

The vehicle speed sensor outputs a 4 pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of these pulse signals.

G036498E03
2.396,0.042 3.354,0.24 0.958,0.198 10 false 4 Pulse Signal 4.115,0.042 5.073,0.24 0.958,0.198 10 false 4 Pulse Signal 5.135,1.354 5.51,1.552 0.375,0.198 10 false ECM 3.146,1.344 4.385,1.552 1.24,0.208 10 false Combination Meter 1.781,1.354 2.677,1.552 0.896,0.198 10 false Transmission

DTC No. DTC Detection Condition Suspected Area
P0500 While vehicle is being driven, no vehicle speed sensor signal to ECM
(2 trip detection logic)
·

Open or short in speed sensor circuit

·

Vehicle speed sensor

·

Combination meter

·

ECM



MONITOR DESCRIPTION

The ECM assumes that the vehicle is being driven when a high engine load continues for 8 seconds or more. If there is no speed signal from the combination meter, despite this condition being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and sets the DTC.

WIRING DIAGRAM

A401745E01
1.719,1.635 1.99,1.823 0.271,0.188 10 false +S 0.74,2.573 1.01,2.76 0.271,0.188 10 false J1 0.719,2.74 2,2.927 1.281,0.188 10 false Combination Meter 5.823,2.594 6.229,2.771 0.406,0.177 10 false ECM 5.323,1.479 5.677,1.656 0.354,0.177 10 false SPD 5.313,2.188 5.552,2.375 0.24,0.188 10 false E1 4.979,2.188 5.281,2.396 0.302,0.208 10 false B73 4.958,1.646 5.26,1.854 0.302,0.208 10 false A53 2.063,1.521 2.219,1.719 0.156,0.198 10 false 6 5.042,1.469 5.198,1.667 0.156,0.198 10 false 8 5.042,2.01 5.198,2.208 0.156,0.198 10 false 3

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH ABS
a.

Confirm the vehicle specifications.


Result:
Result Proceed to
w/ ABS A
w/o ABS B



A

2.READ VALUE USING GTS (VEHICLE SPEED)

B

6.CHECK OPERATION OF SPEEDOMETER
2.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Vehicle Speed.


d.

Drive the vehicle.


e.

Read the value displayed on the GTS.


Result:
Result Proceed to
Values displayed on GTS and speedometer display not equal A
Values displayed on GTS and speedometer display equal B



A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

CHECK FOR INTERMITTENT PROBLEMS

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-6 (+S) - A53-8 (SPD) Always Below 1 Ω
J1-6 (+S) or A53-8 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK COMBINATION METER SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK COMBINATION METER SYSTEM
a.

Check the circuits that send vehicle speed signals to this system in the combination meter system.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Start the engine.


h.

On the GTS, enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT / Data List / All Data / Idle Fuel Cut.


i.

Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more.


j.

Decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel cut.


k.

Stop the vehicle.


l.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

HINT:

If no DTCs (no pending DTCs) are output to the GTS, the repair has been successfully completed.



Result:
Proceed to
NEXT



NEXT

END

6.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

OK:

Speedometer operation is normal.


HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in speedometer malfunction.




Result:
Proceed to
OK
NG



OK

7.INSPECT ECM (SPD VOLTAGE)

NG

CHECK SPEEDOMETER CIRCUIT

7.INSPECT ECM (SPD VOLTAGE)
a.
A430120E01
0.573,0.26 1.01,0.51 0.438,0.25 1.938,0.25 2.375,0.5 0.438,0.25 0.823,0.823 1.094,1.583 true 2.292,0.906 2.5,1.563 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *1 0.656,0.302 0.969,0.5 0.313,0.198 10 false B73 2.031,0.292 2.344,0.49 0.313,0.198 10 false A53 0.229,2.844 0.625,3.198 0.396,0.354 10 false 4.5 to 5.5 V 0.333,3.885 0.625,4.083 0.292,0.198 10 false 0 V 3.031,4.042 3.26,4.24 0.229,0.198 10 false *2 0.896,1.635 1.385,1.844 0.49,0.208 10 false 3 (E1) 2.24,1.625 2.833,1.833 0.594,0.208 10 false 8 (SPD)

Move the transmission gear select lever to the neutral position.


b.

Jack up the vehicle.


c.

Turn the ignition switch to ON.


d.

Measure the voltage of the ECM connectors as the wheel is turned slowly.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A53-8 (SPD) - B73-3 (E1) Ignition switch ON Voltage is generated intermittently


Text in Illustration
*1 Component with harness connected
(ECM)
*2 Wheel Turned

HINT:

The output voltage should fluctuate up and down (as shown in the illustration) when the wheel is turned slowly.



Result:
Proceed to
OK
NG



OK

NG

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the combination meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-6 (+S) - A53-8 (SPD) Always Below 1 Ω
J1-6 (+S) or A53-8 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR