Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies power to terminal BATT of the ECM even when the ignition switch is OFF. This power allows the ECM to store DTC history, freeze frame data, fuel trim values, and other data.

DTC No. DTC Detection Condition Trouble Area
P0560 Open in backup power source circuit1 trip detection logic
·

Open in back-up power source circuit

·

ECM



HINT:

If DTC P0560 is set, the ECM does not store other DTCs.


WIRING DIAGRAM

A401734E01
0.552,2.031 1.438,2.198 0.885,0.167 10 false R/B NO. 2-B 0.552,2.792 1.198,2.979 0.646,0.188 10 false FL MAIN 0.729,3.938 1.375,4.125 0.646,0.188 10 false Battery 1.563,1.354 1.875,1.552 0.313,0.198 10 false P/I 2.708,1.385 3.406,1.563 0.698,0.177 10 false EFI-MAIN 4.156,1.365 4.854,1.542 0.698,0.177 10 false EFI NO. 1 6.333,3.104 6.708,3.281 0.375,0.177 10 false ECM 6.021,2.094 6.292,2.292 0.271,0.198 10 false E1 6.031,1.198 6.427,1.385 0.396,0.188 10 false BATT 5.667,2.094 5.969,2.292 0.302,0.198 10 false B73 5.656,1.198 5.958,1.396 0.302,0.198 10 false A55 5.719,0.99 5.875,1.188 0.156,0.198 10 false 3 5.719,1.906 5.875,2.104 0.156,0.198 10 false 3

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT ECM (BATT VOLTAGE)
a.
A146289E42
0.406,0.208 0.802,0.448 0.396,0.24 2.625,0.208 3.021,0.448 0.396,0.24 0.688,0.75 1.063,1.771 true 2.521,1.792 2.927,0.76 true 0.771,1.802 1.292,2 0.521,0.198 10 false 3 (E1) 2.229,1.813 2.885,2 0.656,0.188 10 false 3 (BATT) 0.479,0.25 0.813,0.438 0.333,0.188 10 false B73 0.146,0.094 0.427,0.271 0.281,0.177 10 false *a 2.698,0.25 3.031,0.438 0.333,0.188 10 false A55

Measure the voltage of the ECM connectors.

Standard Voltage:
Tester Connection Condition Specified Condition
A55-3 (BATT) - B73-3 (E1) Always 11 to 14 V


Text in Illustration
*a Component with harness connected
(to ECM)


Result:
Proceed To
OK
NG



OK

2.CHECK WHETHER DTC OUTPUT RECURS

NG

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS ON.



d.

Turn the ignition switch to OFF and turn the tester OFF.


e.

Start the engine and turn the GTS ON.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read DTCs.


Result:
Result Proceed To
P0560 is output A
No DTC is output B



A

B

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
a.

Disconnect the ECM connector.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the cable from the positive (+) battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-3 (BATT) - Positive (+) battery cable terminal Always Below 1 Ω
A55-3 (BATT) or Positive (+) battery cable terminal - Body ground Always 10 kΩ or higher



Result:
Proceed To
OK
NG



OK

4.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.



Result:
Proceed To
OK
NG



OK

5.INSPECT BATTERY TERMINAL

NG

REPLACE OR RECHARGE BATTERY

5.INSPECT BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.



Result:
Proceed To
OK
NG



OK

REPAIR OR REPLACE FUSIBLE LINK BLOCK

NG

REPAIR OR REPLACE BATTERY TERMINAL