Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:
·

This Electronic Throttle Control System (ETCS) does not use a throttle cable.

·

These DTCs are related to the accelerator pedal position sensor. The troubleshooting procedures for the accelerator pedal position sensor are in the flowchart below.



The Accelerator Pedal Position (APP) sensor is mounted in the accelerator pedal to detect the angle of the accelerator pedal. This sensor is electronically controlled and uses Hall-effect elements.

In the accelerator pedal position sensor, the voltage applied to terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the angle of the accelerator pedal. VPA is a signal to indicate the actual accelerator pedal angle and is used for the engine control. VPA2 is used to detect malfunctions of the sensor itself.

The ECM monitors the accelerator pedal angle from the VPA and VPA2 signal outputs, and controls the throttle motor based on these signals.

A158500E03
0.927,2.552 0.719,1.938 true 0.896,2.896 0.719,3.438 true 0.99,2.281 1.344,1.469 true 1.229,3.792 0.979,3.198 true 4.646,3.344 4.833,3.448 false 5.115,2.802 5.271,2.854 false 5.198,2.396 5.365,2.427 false 0.156,0.75 1.292,1.125 1.135,0.375 10 false Accelerator Pedal Position Sensor 1.344,1.292 2.104,1.49 0.76,0.198 10 false Magnet 1.104,3.802 1.865,4.021 0.76,0.219 10 false Magnet 0.417,1.719 1,1.938 0.583,0.219 10 false No. 1 IC 0.396,3.448 0.979,3.667 0.583,0.219 10 false No. 2 IC 2.063,3.323 2.563,3.521 0.5,0.198 10 false EPA2 2.063,3 2.531,3.188 0.469,0.188 10 false VPA2 2.073,2.396 2.625,2.604 0.552,0.208 10 false VCPA 2.073,2.073 2.458,2.281 0.385,0.208 10 false EPA 2.083,1.729 2.531,1.958 0.448,0.229 10 false VPA 2.677,1.313 3.229,1.521 0.552,0.208 10 false ECM 4.208,0.76 6.823,0.979 2.615,0.219 10 false APP Sensor Output Voltage (V) 4.385,3.979 6.729,4.188 2.344,0.208 10 false Accelerator Pedal Turning Angle (°) 3.646,4.604 6.656,4.813 3.01,0.208 10 false *1: Accelerator Pedal Fully Released 3.635,5.01 6.646,5.219 3.01,0.208 10 false *2: Accelerator Pedal Fully Depressed 4.771,3.615 5.688,3.823 0.917,0.208 10 false Usable Range 3.865,2.219 4.177,2.427 0.313,0.208 10 false 3.89 3.906,2.802 4.177,2.99 0.271,0.188 10 false 1.6 3.948,3.063 4.208,3.271 0.26,0.208 10 false 0.8 5.969,1.448 6.156,1.656 0.188,0.208 10 false *2 4.542,1.469 4.75,1.677 0.208,0.208 10 false *1 4.146,1.875 4.271,2.042 0.125,0.167 10 false 5 5.99,3.375 6.219,3.594 0.229,0.219 10 false 95 3.854,1.979 4.167,2.188 0.313,0.208 10 false 4.55 4.146,2.458 4.271,2.625 0.125,0.167 10 false 3 4.167,2.958 4.292,3.125 0.125,0.167 10 false 1 4.885,3.354 5.25,3.573 0.365,0.219 10 false 2.5 4.552,3.625 4.667,3.844 0.115,0.219 10 false 0 5.771,3.625 6,3.844 0.229,0.219 10 false 80 6.531,3.375 7.125,3.583 0.594,0.208 10 false (Degree) 4.094,1.573 4.323,1.792 0.229,0.219 10 false (V) 5.323,2.792 5.635,3 0.313,0.208 10 false VPA 4.844,2.302 5.219,2.51 0.375,0.208 10 false VPA2

DTC No. DTC Detection Condition Suspected Area
P2120 VPA quickly fluctuates up and down beyond upper and lower malfunction thresholds for 0.5 seconds
(1 trip detection logic)
·

Accelerator pedal position sensor

·

ECM


P2122 Condition (a) continues for 0.5 seconds or more when accelerator pedal is depressed:
(1 trip detection logic)
(a) VPA is 0.2 V or less
·

Accelerator pedal position sensor

·

Open in VCPA circuit

·

Open or ground short in VPA circuit

·

ECM


P2123 Condition (a) continues for 2.0 seconds or more:
(1 trip detection logic)
(a) VPA is 4.8 V or more
·

Accelerator pedal position sensor

·

Open in EPA circuit

·

ECM


P2125 Condition (a) continues for 0.5 seconds or more:
(1 trip detection logic)
(a) VPA2 quickly fluctuates up and down beyond upper and lower malfunction thresholds
·

Accelerator pedal position sensor

·

ECM


P2127 Condition (a) continues for 0.5 seconds or more when accelerator pedal is depressed:
(1 trip detection logic)
(a) VPA2 is 0.5 V or less
·

Accelerator pedal position sensor

·

Open in VCPA circuit

·

Open or ground short in VPA2 circuit

·

ECM


P2128 Conditions (a) and (b) continue for 2.0 seconds or more:
(a) VPA2 is 4.8 V or more
(b) VPA is 0.2 V or more and VPA2 is 3.45 V or less
·

Accelerator pedal position sensor

·

Open in EPA2 circuit

·

ECM


P2138 Condition (a) or (b) continues for 2.0 seconds or more:
(1 trip detection logic)
(a) Difference between VPA and VPA2 is 0.02 V or less
VPA is 0.2 V or less and VPA2 is 0.5 V or less
·

Short in VPA and VPA2 circuits

·

Accelerator pedal position sensor

·

ECM



HINT:

When one or more of DTCs P2120, P2122, P2123, P2125, P2127, P2128 and P2138 are detected, check the output voltage of the accelerator pedal position sensor by selecting the following menu items on the GTS: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.


Suspected Area Accel Position No.1
When AP Released
Accel Position No.2
When AP Released
Accel Position No.1
When AP Depressed
Accel Position No.2
When AP Depressed
VCP circuit open 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or ground short in VPA circuit 0 to 0.2 V 1.3 to 1.9 V 0 to 0.2 V 3.5 to 5.0 V
Open or ground short in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.5 to 4.6 V 0 to 0.2 V
EPA circuit open 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V

HINT:
·

The accelerator pedal position is expressed in terms of voltage.

·

AP stands for accelerator pedal.



MONITOR DESCRIPTION

When either voltage output VPA or VPA2 deviates from the standard range, or the difference between the voltage outputs of the two sensors is less than the threshold, the ECM concludes that there is a defect in the APP sensor. The ECM illuminates the MIL and sets a DTC.

Example:

The voltage output of the VPA is below 0.2 V or exceeds 4.8 V.

This monitor runs for 2 seconds (the first 2 seconds of engine idle) after the engine is started (1 trip detection logic).

FAIL-SAFE

The accelerator pedal position sensor has a main circuit and associated circuit. When one circuit is malfunctioning, the accelerator pedal position is calculated by the output of the other circuit. When both of the circuits are malfunctioning, it is interpreted that the accelerator pedal is released. As a result, the throttle valve is closed and the engine idles.

WIRING DIAGRAM

A401746E01
1.552,0.698 1.927,0.875 0.375,0.177 10 false VPA 1.552,1.135 1.927,1.313 0.375,0.177 10 false EPA 1.458,1.542 1.927,1.719 0.469,0.177 10 false VCPA 1.49,1.969 1.927,2.156 0.438,0.188 10 false VPA2 1.479,2.375 1.917,2.563 0.438,0.188 10 false EPA2 0.302,3 0.542,3.188 0.24,0.188 10 false F9 0.292,3.167 2.49,3.365 2.198,0.198 10 false Accelerator Pedal Position Sensor 6.083,3.031 6.375,3.219 0.292,0.188 10 false A55 6.073,3.198 6.49,3.375 0.417,0.177 10 false ECM 5.573,2.271 6.01,2.458 0.438,0.188 10 false EPA2 5.573,1.844 6.01,2.031 0.438,0.188 10 false VPA2 5.594,1.448 6.063,1.625 0.469,0.177 10 false VCPA 5.583,1.021 5.958,1.198 0.375,0.177 10 false EPA 5.583,0.604 5.958,0.781 0.375,0.177 10 false VPA 2,0.604 2.135,0.781 0.135,0.177 10 false 5 2,1.021 2.135,1.198 0.135,0.177 10 false 3 2,1.438 2.135,1.615 0.135,0.177 10 false 4 2,1.833 2.135,2.01 0.135,0.177 10 false 1 2.01,2.26 2.146,2.438 0.135,0.177 10 false 2 5.292,0.594 5.5,0.771 0.208,0.177 10 false 18 5.292,1.01 5.5,1.188 0.208,0.177 10 false 20 5.281,1.427 5.49,1.604 0.208,0.177 10 false 26 5.281,1.844 5.49,2.021 0.208,0.177 10 false 19 5.281,2.25 5.49,2.427 0.208,0.177 10 false 21

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR POSITION NO. 1, ACCELERATOR POSITION NO. 2)
A208621E08
0.688,1.781 1.156,1.958 0.469,0.177 10 false *a 2.604,1.781 3.052,1.958 0.448,0.177 10 false *b

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.


d.

Read the values.

Standard Voltage:
Accelerator Pedal Accelerator Position No. 1 Accelerator Position No. 2
Released 0.5 to 1.1 V 1.3 to 1.9 V
Depressed 2.5 to 4.6 V 3.5 to 5.0 V


Text in Illustration
*a Depressed
*b Released


Result:
Proceed to
OK
NG



OK

6.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)

NG

2.INSPECT ECM (VCPA VOLTAGE)
2.INSPECT ECM (VCPA VOLTAGE)
a.
A146289E44
2.646,0.167 3.042,0.406 0.396,0.24 2.99,0.927 2.167,1.771 true 2.865,1.677 3.115,1.01 true 2.927,0.917 2.167,0.344 true 1.865,1.792 2.531,2 0.667,0.208 10 false 20 (EPA) 2.594,1.708 3.354,1.906 0.76,0.198 10 true 26 (VCPA ) 2.719,0.198 3.063,0.385 0.344,0.188 10 false A55 0.146,0.094 0.427,0.271 0.281,0.177 10 false *a 1.448,0.219 2.177,0.417 0.729,0.198 10 false 21 (EPA2)

Turn the ignition switch to ON.


b.

Measure the voltage of the ECM connector.

Standard voltage:
Tester Connection Condition Specified Condition
A55-26 (VCPA) - A55-20 (EPA) Ignition switch ON 4.5 to 5.0 V
A55-26 (VCPA) - A55-21 (EPA2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(to ECM)


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (VPA, VPA2 VOLTAGE)

NG

3.INSPECT ECM (VPA, VPA2 VOLTAGE)
a.
A146289E45
2.646,0.167 3.042,0.406 0.396,0.24 2.99,0.927 2.521,1.698 true 2.885,1.646 3.104,0.927 true 2.927,0.927 1.885,1.802 true 3.052,0.917 2.406,0.333 true 2.135,1.771 2.802,1.979 0.667,0.208 10 false 20 (EPA) 2.75,1.677 3.385,1.896 0.635,0.219 10 true 18 (VPA) 2.719,0.198 3.063,0.385 0.344,0.188 10 false A55 0.146,0.094 0.427,0.271 0.281,0.177 10 false *a 1.302,1.802 2.031,2 0.729,0.198 10 false 21 (EPA2) 1.688,0.188 2.427,0.385 0.74,0.198 10 false 19 (VPA2 )

Turn the ignition switch to ON.


b.

Measure the voltage of the ECM connector.

Standard voltage:
Tester Connection Accelerator Pedal Condition Specified Condition
A55-18 (VPA) - A55-20 (EPA) Released 0.5 to 1.1 V
A55-18 (VPA) - A55-20 (EPA) Depressed 2.5 to 4.6 V
A55-19 (VPA2) - A55-21 (EPA2) Released 1.3 to 1.9 V
A55-19 (VPA2) - A55-21 (EPA2) Depressed 3.5 to 5.0 V


Text in Illustration
*a Component with harness connected
(to ECM)


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
4.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance of the wire harness side connectors.

Standard Resistance:
Tester Connection Condition Specified Condition
F9-5 (VPA) - A55-18 (VPA) Always Below 1 Ω
F9-3 (EPA) - A55-20 (EPA) Always Below 1 Ω
F9-4 (VCPA) - A55-26 (VCPA) Always Below 1 Ω
F9-1 (VPA2) - A55-19 (VPA2) Always Below 1 Ω
F9-2 (EPA2) - A55-21 (EPA2) Always Below 1 Ω
F9-5 (VPA) or A55-18 (VPA) - Body ground Always 10 kΩ or higher
F9-3 (EPA) or A55-20 (EPA) - Body ground Always 10 kΩ or higher
F9-4 (VCPA) or A55-26 (VCPA) - Body ground Always 10 kΩ or higher
F9-1 (VPA2) or A55-19 (VPA2) - Body ground Always 10 kΩ or higher
F9-2 (EPA2) or A55-21 (EPA2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE ACCELERATOR PEDAL ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ACCELERATOR PEDAL ASSEMBLY
a.

Replace the accelerator pedal sensor assembly (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL).


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
6.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS ON.



d.

Start the engine.


e.

Idle the engine for 15 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.



Result:
Display (DTC Output) Proceed To
One or more of P2120, P2122, P2123, P2125, P2127, P2128 and P2138 A
No output B



A

B

END