Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P2238  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)  P2239  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)  P2252  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)  P2253  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)  


DESCRIPTION

HINT:

These DTCs are related to the A/F sensor.


The Air-fuel Ratio (A/F) sensor generates a voltage* in response to the actual air-fuel ratio. The sensor output voltage provides feedback to the ECM. The ECM uses the feedback to control the air-fuel ratio. Using the sensor output voltage, the ECM determines the deviation from the stoichiometric air-fuel ratio, and regulates the injection time. If the A/F sensor is malfunctioning, the ECM is unable to control the air-fuel ratio accurately.

The A/F sensor is equipped with a heater which heats the zirconia element. The heater is also controlled by the ECM. When the intake air volume is low (the temperature of the exhaust gas is low), a current flows to the heater to heat the sensor to facilitate the detection of accurate oxygen concentration.

The A/F sensor is a planar type. Compared to the conventional type, the sensor and heater portions are narrower. The heat of the heater is conducted to the zirconia element through the alumina, accelerating sensor activation.

To obtain a high purification rate of carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) in the exhaust gas, the Three-Way Catalytic Converter (TWC) is used. The TWC is most efficient when the air-fuel ratio is maintained near the stoichiometric air-fuel ratio.

HINT:

*: The voltage value changes inside the ECM only.


G038016E09
1.625,2.219 1.271,1.906 1.271,1.906 1.219,1.906 true 1.76,2.156 2.021,1.885 2.021,1.885 2.073,1.885 false 2.948,1.229 3.313,0.313 3.313,0.313 3.438,0.313 true 3.125,1.219 3.26,0.927 3.26,0.927 3.458,0.927 true 3.24,1.302 3.448,1.302 true 2.885,1.667 2.948,1.583 2.948,1.583 3.438,1.583 true 3.021,1.688 3.115,1.594 true 3.094,1.885 3.438,1.885 true 0.177,2.385 1.156,2.583 0.979,0.198 10 false Exhaust Gas 0.635,1.802 1.229,2 0.594,0.198 10 false Element 2.125,1.802 2.594,2 0.469,0.198 10 false Cover 1.177,2.448 1.323,2.646 0.146,0.198 10 false A 1.948,2.458 2.094,2.656 0.146,0.198 10 false A 3.49,0.219 4.719,0.417 1.229,0.198 10 false Solid Electrolyte 3.458,0.542 4.854,0.74 1.396,0.198 10 false (Zirconia Element) 3.51,0.844 4.146,1.042 0.635,0.198 10 false Alumina 3.51,1.188 4.042,1.385 0.531,0.198 10 false Heater 3.479,1.5 4.708,1.698 1.229,0.198 10 false Platinum Electrode 3.5,1.802 4.583,1.99 1.083,0.188 10 false Atmospheric Air 3.396,2.25 4.792,2.448 1.396,0.198 10 false A-A Cross Section 4.688,0.729 4.948,0.927 0.26,0.198 10 false 4.0 4.688,1.01 4.948,1.208 0.26,0.198 10 false 3.5 4.688,1.323 4.948,1.521 0.26,0.198 10 false 3.0 4.688,1.656 4.948,1.854 0.26,0.198 10 false 2.5 4.688,2.021 4.948,2.219 0.26,0.198 10 false 2.0 5.135,2.281 5.344,2.479 0.208,0.198 10 false 12 5.427,2.281 5.635,2.479 0.208,0.198 10 false 13 5.708,2.281 5.917,2.479 0.208,0.198 10 false 14 5.948,2.281 6.156,2.479 0.208,0.198 10 false 15 6.208,2.281 6.417,2.479 0.208,0.198 10 false 16 6.448,2.281 6.656,2.479 0.208,0.198 10 false 17 6.646,2.281 6.854,2.479 0.208,0.198 10 false 18 5.031,0.052 6.292,0.406 1.26,0.354 10 false ECM Monitored A/F Sensor Voltage

DTC No. DTC Detection Condition Trouble Area
P2238
·

Condition (a) or (b) continues for 5.0 seconds or more:

(2 trip detection logic)

(a) AF+ is 0.5 V or less

(b) (AF+) - (AF-) is 0.1 V or less

·

A/F sensor admittance: Less than 0.022 1/Ω


·

Open or short in A/F sensor (sensor 1) circuit

·

A/F sensor (sensor 1)

·

A/F sensor heater

·

NO. 2 integration relay

·

A/F sensor heater and A/F relay circuits

·

ECM


P2239 Condition (a) or (b) continues for 5.0 seconds or more:
(2 trip detection logic)
(a) AF+ is more than 4.5 V
(b) (AF+) - (AF-) is more than 0.8 V
·

Open or short in A/F sensor (sensor 1) circuit

·

A/F sensor (sensor 1)

·

A/F sensor heater

·

NO. 2 integration relay

·

A/F sensor heater and A/F relay circuits

·

ECM


P2252 AF- is 0.5 V or less for 5.0 seconds or more
(2 trip detection logic)
·

Open or short in A/F sensor (sensor 1) circuit

·

A/F sensor (sensor 1)

·

A/F sensor heater

·

NO. 2 integration relay

·

A/F sensor heater and A/F relay circuits

·

ECM


P2253 AF- is more than 4.5 V for 5.0 seconds or more
(2 trip detection logic)
·

Open or short in A/F sensor (sensor 1) circuit

·

A/F sensor (sensor 1)

·

A/F sensor heater

·

NO. 2 integration relay

·

A/F sensor heater and A/F relay circuits

·

ECM



WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

GTS only:

Malfunctioning areas can be found by performing the Active Test / A/F Control operation. The A/F Control operation can determine if the A/F sensor, heated oxygen sensor or other potential trouble areas are malfunctioning or not.


(a) Perform Active Test using the GTS.

HINT:
1.

Connect the GTS to the DLC3.

2.

Start the engine and turn the GTS on.

3.

Warm up the engine by running the engine at 2,500 rpm for approximately 90 seconds.

4.

On the GTS, select the following menu items: Powertrain / Engine and ECT / Active Test /Control the Injection Volume for A/F Sensor.

5.

Select the following monitor items: AFS B1S1 and O2S B1S2.

6.

Perform the A/F Control operation with the engine in an idling condition (press the right or left button).



HINT:
·

The A/F control operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Standard:
Tester Display
(Sensor)
Injection Volume Status Voltage
AFS B1S1 or AFS B1 S1
(A/F)
+25% Rich Less than 3.0 V
AFS B1S1 or AFS B1 S1
(A/F)
-12.5% Lean More than 3.35 V
O2S B1 S2
(HO2)
+25% Rich More than 0.55 V
O2S B1 S2
(HO2)
-12.5% Lean Less than 0.4 V


NOTICE:

The A/F sensor output has a few seconds of delay and the heated oxygen sensor output has about 20 seconds of delay at maximum.


A430115E01
5.792,3.74 6.792,3.948 1,0.208 10 false - A/F sensor 3.667,4.927 4.531,5.104 0.865,0.177 8 false Less than 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.594,4.698 4.542,4.885 0.948,0.188 8 false More than 0.55 V 0.917,2.625 1.885,2.792 0.969,0.167 8 false More than 3.35 V 0.979,2.885 1.875,3.063 0.896,0.177 8 false Less than 3.0 V 1.563,1.604 1.927,1.781 0.365,0.177 8 false +25% 1.49,1.833 1.917,2.01 0.427,0.177 8 false -12.5% 3.573,2.604 4.531,2.771 0.958,0.167 8 false More than 0.55 V 3.635,2.844 4.49,3.01 0.854,0.167 8 false Less than 0.4 V 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.885,6.958 0.969,0.188 8 false More than 3.35 V 0.99,7 1.896,7.167 0.906,0.167 8 false Less than 3.0 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.115,0.49 0.49,0.719 0.375,0.229 10 false Case 0.635,0.573 3.063,0.771 2.427,0.198 10 false A/F Sensor (Sensor 1) Output Voltage 3.24,0.594 5.667,0.802 2.427,0.208 10 false HO2 Sensor (Sensor 2) Output Voltage 5.938,0.469 6.979,0.885 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4.135 7.073,4.333 1.271,0.198 10 false - A/F sensor heater 5.802,4.594 7.083,4.792 1.281,0.198 10 false - A/F sensor circuit 5.844,5.51 6.896,5.885 1.052,0.375 10 false - HO2 sensor 5.844,6.135 6.708,6.479 0.865,0.344 10 false - HO2 sensor heater 5.844,6.75 6.719,7.115 0.875,0.365 10 false - HO2 sensor circuit 5.823,7.51 6.594,7.698 0.771,0.188 10 false - Injector 5.813,7.844 6.969,8.177 1.156,0.333 10 false - Fuel pressure 5.802,8.24 7.094,8.948 1.292,0.708 10 false - Gas leak from exhaust system (Air-fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG 1.5,3.677 1.865,3.833 0.365,0.156 8 false +25% 4.083,1.594 4.427,1.781 0.344,0.188 8 false +25% 4.104,3.656 4.458,3.844 0.354,0.188 8 false +25% 1.427,3.875 1.854,4.052 0.427,0.177 8 false -12.5% 4.021,1.823 4.448,2 0.427,0.177 8 false -12.5% 4.021,3.896 4.448,4.073 0.427,0.177 8 false -12.5% 1.479,5.75 1.865,5.938 0.385,0.188 8 false +25% 1.469,7.771 1.823,7.948 0.354,0.177 8 false +25% 4.104,7.792 4.479,7.979 0.375,0.188 8 false +25% 4.167,5.729 4.531,5.896 0.365,0.167 8 false +25% 1.406,5.948 1.833,6.125 0.427,0.177 8 false -12.5% 1.396,8.01 1.823,8.188 0.427,0.177 8 false -12.5% 4.031,8.021 4.458,8.198 0.427,0.177 8 false -12.5% 4.083,5.938 4.51,6.115 0.427,0.177 8 false -12.5%

The following A/F control procedure enables the technicians to check and graph the output voltages of both A/F sensor and heated oxygen sensor.

To display the graph, select the following menu items on the tester: View / Line graph.


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check the conditions that would cause the engine to run with the rich air-fuel mixture.

·

A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check the conditions that would cause the engine to run with the lean air-fuel mixture.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B88-1 (HA1A) - B73-1 (HA1A) Always Below 1 Ω
B88-3 (A1A+) - B73-21 (A1A+) Always Below 1 Ω
B88-4 (A1A-) - B73-31 (A1A-) Always Below 1 Ω
B88-1 (HA1A) or B73-1 (HA1A) - Body ground Always 10 kΩ or higher
B88-3 (A1A+) or B73-21 (A1A+) - Body ground Always 10 kΩ or higher
B88-4 (A1A-) or B73-31 (A1A-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2237, P2238, P2239, P2252 OR P2253)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2237, P2238, P2239, P2252 OR P2253)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Allow the engine to idle for 5 minutes or more.


h.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


i.

Read the pending DTCs.


Result:
Result Proceed to
No DTC is output A
P2238, P2239, P2252 or P2253 is output B



A

END

B