Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  


DESCRIPTION

HINT:
·

Although "oxygen sensor" is in the DTC titles, these DTCs are related to the air-fuel ratio (A/F) sensor.

·

Sensor 1 refers to the sensor mounted before the Three-Way Catalytic Converter (TWC) and is located near the engine assembly.

·

Sensor 2 refers to the sensor mounted after the TWC and is located far from the engine assembly.



The Air-fuel Ratio (A/F) sensor generates a voltage* in response to the actual air-fuel ratio. The sensor output voltage provides feedback to the ECM. The ECM uses the feedback to control the air-fuel ratio. Using the sensor output voltage, the ECM determines the deviation from the stoichiometric air-fuel ratio, and regulates the injection time. If the A/F sensor is malfunctioning, the ECM is unable to control the air-fuel ratio accurately.

The A/F sensor is equipped with a heater which heats the zirconia element. The heater is also controlled by the ECM. When the intake air volume is low (the temperature of the exhaust gas is low), a current flows to the heater to heat the sensor to facilitate the detection of accurate oxygen concentration.

The A/F sensor is a planar type. Compared to the conventional type, the sensor and heater portions are narrower. The heat of the heater is conducted to the zirconia element through the alumina, accelerating sensor activation.

To obtain a high purification rate of carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) in the exhaust gas, the Three-Way Catalytic Converter (TWC) is used. The TWC is most efficient when the air-fuel ratio is maintained near the stoichiometric air-fuel ratio.

G038016E08
1.625,2.219 1.271,1.906 1.271,1.906 1.219,1.906 true 1.76,2.156 2.021,1.885 2.021,1.885 2.073,1.885 false 2.948,1.229 3.313,0.313 3.313,0.313 3.438,0.313 true 3.125,1.219 3.26,0.927 3.26,0.927 3.458,0.927 true 3.24,1.302 3.448,1.302 true 2.885,1.667 2.948,1.583 2.948,1.583 3.438,1.583 true 3.021,1.688 3.115,1.594 true 3.094,1.885 3.438,1.885 true 0.177,2.385 1.156,2.583 0.979,0.198 10 false Exhaust Gas 0.635,1.802 1.229,2 0.594,0.198 10 false Element 2.125,1.802 2.594,2 0.469,0.198 10 false Cover 1.177,2.448 1.323,2.646 0.146,0.198 10 false A 1.948,2.458 2.094,2.656 0.146,0.198 10 false A 3.49,0.219 4.719,0.417 1.229,0.198 10 false Solid Electrolyte 3.458,0.542 4.854,0.74 1.396,0.198 10 false (Zirconia Element) 3.51,0.844 4.146,1.042 0.635,0.198 10 false Alumina 3.51,1.188 4.042,1.385 0.531,0.198 10 false Heater 3.479,1.5 4.708,1.698 1.229,0.198 10 false Platinum Electrode 3.5,1.802 4.583,1.99 1.083,0.188 10 false Atmospheric Air 3.396,2.25 4.792,2.448 1.396,0.198 10 false A-A Cross Section 4.688,0.729 4.948,0.927 0.26,0.198 10 false 4.0 4.688,1.01 4.948,1.208 0.26,0.198 10 false 3.5 4.688,1.323 4.948,1.521 0.26,0.198 10 false 3.0 4.688,1.656 4.948,1.854 0.26,0.198 10 false 2.5 4.688,2.021 4.948,2.219 0.26,0.198 10 false 2.0 5.135,2.281 5.344,2.479 0.208,0.198 10 false 12 5.427,2.281 5.635,2.479 0.208,0.198 10 false 13 5.708,2.281 5.917,2.479 0.208,0.198 10 false 14 5.948,2.281 6.156,2.479 0.208,0.198 10 false 15 6.208,2.281 6.417,2.479 0.208,0.198 10 false 16 6.448,2.281 6.656,2.479 0.208,0.198 10 false 17 6.646,2.281 6.854,2.479 0.208,0.198 10 false 18 5.031,0.052 6.292,0.406 1.26,0.354 10 false ECM Monitored A/F Sensor Voltage

HINT:

*: The voltage value changes inside the ECM only.

The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The A/F sensor heater circuit uses a relay on the +B side of the circuit.


A164715E43
0.125,0.094 2.188,0.292 2.063,0.198 10 false Reference (System Diagram): 5.052,1.219 5.479,1.396 0.427,0.177 10 false HA1A 3.948,1.229 4.375,1.417 0.427,0.188 10 false HA1A 3.292,1.25 3.531,1.406 0.24,0.156 10 false +B 5.052,1.75 5.563,1.948 0.51,0.198 10 false A1A+ 3.948,1.76 4.354,1.99 0.406,0.229 10 false A1A+ 5.052,2.49 5.438,2.677 0.385,0.188 10 false A1A- 3.271,1.76 3.667,1.958 0.396,0.198 10 false A1A- 2.292,2.844 3.323,3.042 1.031,0.198 10 false from EFI Relay 3.542,1.51 4.01,1.688 0.469,0.177 10 false Heater 3.531,2.042 4,2.24 0.469,0.198 10 false Sensor 1.885,2.375 2.469,2.563 0.583,0.188 10 false A/F HTR 1.094,1.51 1.708,1.688 0.615,0.177 10 false A/F HTR 3.125,2.365 4.531,2.563 1.406,0.198 10 false Air Fuel Ratio Sensor 0.24,1.24 0.76,1.615 0.521,0.375 10 false from P/I fuse 5.781,2.938 6.229,3.094 0.448,0.156 10 false ECM 6.26,1.833 6.75,2.208 0.49,0.375 10 false Duty Control

DTC No. DTC Detection Condition Trouble Area
P0031 Heated current is 0.8 A or less when heater operates
(1 trip detection logic)
·

Open in heater circuit of A/F sensor

·

A/F sensor heater

·

NO. 2 integration relay

·

ECM


P0032 Heated current exceeds 10 A when heater operates
(1 trip detection logic)
·

Short in heater circuit of A/F sensor

·

A/F sensor heater

·

NO. 2 integration relay

·

ECM



MONITOR DESCRIPTION

The ECM uses A/F sensor information to keep the air-fuel ratio close to the stoichiometric ratio. This maximizes the catalytic converter's ability to purify exhaust gases. The sensor detects oxygen levels in the exhaust gas and sends this signal to the ECM.

The inner surface of the sensor element is exposed to outside air. The outer surface of the sensor element is exposed to exhaust gas. The sensor element is made of platinum coated zirconia and includes an integrated heating element. The zirconia element generates a small voltage when there is a large difference in the oxygen concentration of the exhaust and outside air. The platinum coating amplifies the voltage generation. When the sensor is heated, the sensor becomes very efficient. If the temperature of the exhaust is low, the sensor will not generate useful voltage signals without supplemental heating. The ECM regulates the supplemental heating using a duty-cycle approach to regulate the average current in the heater element. If the heater current is out of the normal range, the sensor's output signals will be inaccurate and the ECM cannot regulate the A/F properly.

When the heater current is out of the normal operating range, the ECM interprets this as a malfunction and stores a DTC.

WIRING DIAGRAM

A395983E01
0.417,0.656 0.719,0.833 0.302,0.177 10 false P/I 0.344,1.51 0.635,2.063 0.292,0.552 10 false R/B NO. 2-B 0.354,2.75 0.719,3.125 0.365,0.375 10 false FL MAIN 0.479,4.094 1.031,4.302 0.552,0.208 10 false Battery 1.438,0.635 2.042,0.813 0.604,0.177 10 false A/F HTR 2.115,1.302 2.719,1.479 0.604,0.177 10 false A/F HTR 1.333,2.49 2,2.667 0.667,0.177 10 false EFI-MAIN 2.25,3.146 2.604,3.333 0.354,0.188 10 false EFI 1.417,3.99 2.99,4.188 1.573,0.198 10 false NO. 2 Integration Relay 2.969,3.583 3.26,3.76 0.292,0.177 10 false 2D 2.958,2.792 3.25,2.969 0.292,0.177 10 false 2D 2.969,2.323 3.26,2.5 0.292,0.177 10 false 2D 2.969,1.677 3.26,1.854 0.292,0.177 10 false 2D 2.979,0.958 3.271,1.135 0.292,0.177 10 false 2D 2.969,0.5 3.26,0.677 0.292,0.177 10 false 2D 0.938,0.5 1.229,0.677 0.292,0.177 10 false 2E 3.01,3.375 3.156,3.552 0.146,0.177 10 false 2 3,2.604 3.146,2.781 0.146,0.177 10 false 3 3.021,2.125 3.167,2.302 0.146,0.177 10 false 4 3.01,1.479 3.156,1.656 0.146,0.177 10 false 6 3.021,0.76 3.167,0.938 0.146,0.177 10 false 7 3.021,0.292 3.167,0.469 0.146,0.177 10 false 8 6.021,0.5 6.354,0.688 0.333,0.188 10 false B73 6.021,1.146 6.354,1.333 0.333,0.188 10 false B73 6.021,1.979 6.354,2.167 0.333,0.188 10 false B73 6.021,3.583 6.354,3.771 0.333,0.188 10 false A55 6.396,3.573 6.833,3.76 0.438,0.188 10 false MREL 6.406,1.979 6.844,2.167 0.438,0.188 10 false A1A- 6.406,1.146 6.844,1.333 0.438,0.188 10 false A1A+ 6.406,0.49 6.844,0.677 0.438,0.188 10 false HA1A 0.99,0.292 1.135,0.469 0.146,0.177 10 false 1 3.875,0.396 4.021,0.573 0.146,0.177 10 false 2 3.885,1.031 4.031,1.208 0.146,0.177 10 false 4 4.094,0.385 4.385,0.573 0.292,0.188 10 false +B 4.094,1.031 4.5,1.229 0.406,0.198 10 false A1A- 4.708,0.365 5.156,0.552 0.448,0.188 10 false HA1A 4.76,1.021 5.167,1.198 0.406,0.177 10 false A1A+ 5.208,0.385 5.354,0.563 0.146,0.177 10 false 1 5.208,1.031 5.354,1.208 0.146,0.177 10 false 3 4.031,1.542 4.365,1.729 0.333,0.188 10 false B88 4.031,1.688 5.427,1.865 1.396,0.177 10 false Air Fuel Ratio Sensor 4.177,2.417 4.99,2.604 0.813,0.188 10 false *: Shielded 5.542,0.833 5.698,0.99 0.156,0.156 10 false * 6.521,4.104 6.958,4.292 0.438,0.188 10 false ECM 6.094,0.292 6.24,0.469 0.146,0.177 10 false 1 6.063,0.927 6.302,1.115 0.24,0.188 10 false 21 6.052,1.771 6.292,1.958 0.24,0.188 10 false 31 6.083,3.375 6.229,3.552 0.146,0.177 10 false 8

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the air fuel ratio sensor output voltage (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST). If the sensor output voltage does not change (almost no reaction) while performing the Active test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)
a.
A208632E16
0.271,0.958 0.719,1.229 0.448,0.271 1.833,0.865 2.281,0.51 true 0.115,0.104 0.375,0.333 0.26,0.229 10 false *a 2.344,0.396 2.667,0.604 0.323,0.208 10 false +B 0.354,1 0.646,1.208 0.292,0.208 10 false B88

Disconnect the air fuel ratio sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B88-2 (+B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

5.INSPECT NO. 2 INTEGRATION RELAY (A/F HTR RELAY)
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B88-1 (HA1A) - B73-1 (HA1A) Always Below 1 Ω
B88-1 (HA1A) or B73-1 (HA1A) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and idle it for 5 minutes or more.


g.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute.


h.

Idle the engine for 5 minutes or more.


i.

Read the output pending DTCs using the GTS.


Result:
Result Proceed to
No pending DTC is output A
Pending DTC P0031 or P0032 is output B



A

B

5.INSPECT NO. 2 INTEGRATION RELAY (A/F HTR RELAY)
a.

Inspect the NO. 2 integration relay (A/F HTR relay) (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - AIR FUEL RATIO SENSOR, BODY GROUND)

NG

REPLACE NO. 2 INTEGRATION RELAY

6.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - AIR FUEL RATIO SENSOR, BODY GROUND)
a.

Disconnect the air fuel ratio sensor connector.


b.

Remove the NO. 2 integration relay from the NO. 2 relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-8 - B88-2 (+B) Always Below 1 Ω
2D-4 - 2D-6 Always Below 1 Ω
2D-7 - Body ground Always Below 1 Ω
2D-8 or B88-2 (+B) - Body ground Always 10 kΩ or higher
2D-4 or 2D-6 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR