Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

·

For the circuit diagram of the ECM power source refer to the ECM power source circuit (Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit).

·

VC Power Source Circuit


A395980E01
0.75,0.875 1.063,1.073 0.313,0.198 10 false F9 0.75,1.052 1.885,1.417 1.135,0.365 10 false Accelerator Pedal Position Sensor 1.979,1.063 2.51,1.26 0.531,0.198 10 false VCPA 2.073,1.531 2.479,1.74 0.406,0.208 10 false VPA 2,1.958 2.615,2.208 0.615,0.25 10 false VPA2 2.073,2.375 2.438,2.594 0.365,0.219 10 false EPA 2,2.802 2.521,3.042 0.521,0.24 10 false EPA2 2.51,2.646 2.823,2.844 0.313,0.198 10 false 2 2.51,2.229 2.823,2.427 0.313,0.198 10 false 3 2.51,1.823 2.823,2.021 0.313,0.198 10 false 1 2.521,1.385 2.833,1.583 0.313,0.198 10 false 5 2.521,0.948 2.833,1.146 0.313,0.198 10 false 4 4.667,0.865 4.979,1.063 0.313,0.198 10 false 26 4.635,1.063 5.01,1.281 0.375,0.219 10 false A55 4.99,0.948 5.5,1.167 0.51,0.219 10 false VCPA 5,1.521 5.406,1.74 0.406,0.219 10 false VPA 4.667,1.333 4.979,1.531 0.313,0.198 10 false 18 4.635,1.521 4.948,1.719 0.313,0.198 10 false A55 4.667,1.76 4.979,1.958 0.313,0.198 10 false 19 4.635,1.948 4.958,2.146 0.323,0.198 10 false A55 4.979,1.938 5.438,2.156 0.458,0.219 10 false VPA2 4.99,2.271 5.427,2.479 0.438,0.208 10 false EPA 4.677,2.177 4.99,2.375 0.313,0.198 10 false 20 4.635,2.365 4.948,2.563 0.313,0.198 10 false A55 4.677,2.594 4.99,2.792 0.313,0.198 10 false 21 4.99,2.677 5.583,2.896 0.594,0.219 10 false EPA2 5,3.76 5.313,3.958 0.313,0.198 10 false VC 4.656,3.677 4.969,3.875 0.313,0.198 10 false 18 4.677,4.135 4.99,4.333 0.313,0.198 10 false 20 5,4.333 5.552,4.542 0.552,0.208 10 false VTA1 5,4.781 5.448,5.01 0.448,0.229 10 false VTA2 4.667,4.583 4.979,4.781 0.313,0.198 10 false 19 4.667,5.021 4.979,5.219 0.313,0.198 10 false 28 5.01,5.104 5.323,5.302 0.313,0.198 10 false E2 4.677,6.542 4.99,6.74 0.313,0.198 10 false 25 4.635,6.74 4.948,6.938 0.313,0.198 10 false B73 5,6.74 5.573,6.958 0.573,0.219 10 false VAF*1 5.615,7.813 6.042,8.01 0.427,0.198 10 false ECM 4.156,5.958 4.469,6.156 0.313,0.198 10 false *1 3.271,5.604 3.583,5.802 0.313,0.198 10 false *1 0.406,8.271 2.104,8.542 1.698,0.271 10 false *1: w/ Variable Resistor 0.75,5.979 1.063,6.177 0.313,0.198 10 false B90 0.75,6.188 2.042,6.417 1.292,0.229 10 false Variable Resistor*1 2.156,6.156 2.469,6.354 0.313,0.198 10 false VC 2.083,6.729 2.51,6.979 0.427,0.25 10 false VAF 2.167,7.365 2.479,7.563 0.313,0.198 10 false E2 2.51,7.25 2.823,7.448 0.313,0.198 10 false 1 2.51,6.625 2.823,6.823 0.313,0.198 10 false 3 2.5,6.042 2.813,6.24 0.313,0.198 10 false 2 2.51,5.083 2.823,5.281 0.313,0.198 10 false 3 2.51,4.635 2.823,4.833 0.313,0.198 10 false 4 2.51,4.198 2.823,4.396 0.313,0.198 10 false 6 2.51,3.771 2.823,3.969 0.313,0.198 10 false 5 2.156,3.906 2.469,4.104 0.313,0.198 10 false VC 2.073,4.323 2.458,4.542 0.385,0.219 10 false VTA 2.01,4.781 2.438,5.01 0.427,0.229 10 false VTA2 2.177,5.229 2.49,5.427 0.313,0.198 10 false E2 0.75,3.75 1.115,3.948 0.365,0.198 10 false B65 0.74,3.948 1.771,4.313 1.031,0.365 10 false Throttle Position Sensor 4.625,2.781 4.938,2.979 0.313,0.198 10 false A55 4.635,5.219 4.948,5.417 0.313,0.198 10 false B73 4.635,4.781 4.948,4.979 0.313,0.198 10 false B73 4.635,4.333 4.948,4.531 0.313,0.198 10 false B73 4.635,3.875 4.948,4.073 0.313,0.198 10 false B73

CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH ABS
a.

Confirm the vehicle specifications.

Result:
Result Proceed to
w/ ABS A
w/o ABS B




A

2.READ VALUE USING GTS

B

8.CHECK MIL
2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B




A

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.

Turn the ignition switch to ON.


b.
A146289E41
2.667,0.25 3.063,0.49 0.396,0.24 2.531,1.708 3.104,0.76 true 2.385,1.781 2.844,1.99 0.458,0.208 10 false 1(+B ) 2.729,0.292 3.115,0.531 0.385,0.24 10 false A55 0.146,0.094 0.49,0.333 0.344,0.24 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A55-1(+B) - Body ground Ignition switch ON 11 to 14 V


Text in illustration
*a Component with harness connected
(ECM)

HINT:

If the result is not as specified, since current is not flowing to the +B terminals of the ECM, the system may not be started.



Result:
Proceed to
OK
NG



OK

4.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

4.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle with motor body assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B




A

5.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

B

5.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible
(w/ Variable Resistor)
A
Communication is not possible
(w/o Variable Resistor)
B
Communication is possible C



A

6.CHECK CONNECTION BETWEEN GTS AND ECM (VARIABLE RESISTOR)

B

7.CHECK HARNESS AND CONNECTOR

C

6.CHECK CONNECTION BETWEEN GTS AND ECM (VARIABLE RESISTOR)
a.

Disconnect the variable resistor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B




A

7.CHECK HARNESS AND CONNECTOR

B

7.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Disconnect the variable resistor connector*1.


d.

Disconnect the ECM connectors.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-26 (VCPA) - Body ground Always 10 kΩ or higher
B73-18 (VC) - Body ground Always 10 kΩ or higher


*1: w/ Variable Resistor


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK MIL
a.

Check that MIL (Malfunction Indicator Lamp) lights up when turning the ignition switch to ON.

OK:

MIL lights up



Result:
Proceed to
OK
NG



OK

9.CHECK CONNECTION BETWEEN GTS AND ECM

NG

SYSTEM OK

9.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the tester ON.


c.

Check the connection between the GTS and ECM.


Result:
Condition Proceed to
Communication is not possible A
Communication is possible B



A

10.CHECK MIL (THROTTLE POSITION SENSOR)

B

GO TO MIL CIRCUIT

10.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Condition Proceed to
MIL does not illuminate A
MIL illuminates B



A

11.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)

B

11.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Condition Proceed to
MIL does not illuminate
(w/ Variable Resistor)
A
MIL does not illuminate
(w/o Variable Resistor)
B
MIL illuminates C



A

12.CHECK MIL (VARIABLE RESISTOR)

B

13.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

C

12.CHECK MIL (VARIABLE RESISTOR)
a.

Disconnect the variable resistor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Condition Proceed to
MIL does not illuminate A
MIL illuminates B



A

13.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

B

13.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the accelerator pedal position sensor connector.


c.

Disconnect the variable resistor connector*1.


d.

Disconnect the ECM connectors.


e.

Measure the resistance of the wire harness side connector.

Standard Resistance:
Tester Connection Condition Specified Condition
B73-18 (VC) - Body ground Always 10 kΩ or higher
A55-26 (VCPA) - Body ground Always 10 kΩ or higher


*1: w/ Variable Resistor


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR