While the engine is being cranked, current flows from terminal ST2 of the ignition switch to the starter relay and also flows to terminal STA of the ECM (STA signal).
Refer to DTC P0617 (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>P0617).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check if the engine can be cranked.
| Result | Proceed to |
|---|---|
| Engine cannot be cranked | A |
| Engine can be cranked | B |
A
B
Inspect the starter relay assembly (Click hereEngine / Hybrid System>N04C-VL (STARTING)>STARTER RELAY>ON-VEHICLE INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the starter relay from the No. 2 relay block.
Disconnect the ignition switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J63-9 (ST2) - A57-6 (STA) | Always | Below 1 Ω |
| 1 (ST relay holder) - A57-6 (STA) | Always | Below 1 Ω |
| J63-9 (ST2) or A57-6 (STA) - Body ground | Always | 10 kΩ or higher |
| 1 (ST relay holder) or A57-6 (STA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly (Click hereEngine / Hybrid System>N04C-VL (STARTING)>IGNITION SWITCH>INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the STARTER relay from the No. 2 relay block.
Disconnect the cable from the negative(-) battery terminal.
Disconnect the cable from the positive(+) battery terminal.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (ST relay holder) - Battery positive (+) terminal | Always | Below 1 Ω |
| 3 (ST relay holder) - B99-1 (ST) | Always | Below 1 Ω |
| 5 (ST relay holder) or Battery positive (+) terminal - Body ground | Always | 10 kΩ or higher |
| 3 (ST relay holder) or B99-1 (ST) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the valve displayed on the GTS when the ignition switch is turned to ON and START position.
| Ignition Switch Condition | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the starter relay from the No. 2 relay block.
Disconnect the ignition switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J63-9 (ST2) - A57-6 (STA) | Always | Below 1 Ω |
| J63-9 (ST2) or A57-6 (STA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG