Home › Engine / Hybrid System › N04C-VL (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073159 N04C-VL ENGINE CONTROL _0357053 ECD SYSTEM C

N04C-VL ENGINE CONTROL  ECD SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) for more than 20 seconds.

DTC No. DTC Detection Condition Trouble Area
P0617 When conditions (a), (b) and (c) are met, positive (+B) battery voltage of 10.5 V or more is applied to ECM for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.4 mph)
(b) Engine speed is more than 1000 rpm
(c) STA signal is ON
·

Starter signal circuit

·

Ignition switch assembly

·

ECM



WIRING DIAGRAM

A403473E02
1.198,0.948 1.656,1.146 0.458,0.198 10 false AM2 3.625,0.938 4.25,1.125 0.625,0.188 10 false ST NO. 2 1.875,1.875 2.5,2.063 0.625,0.188 10 false ST NO. 1 0.729,3.052 1.354,3.24 0.625,0.188 10 false FL MAIN 2.76,4.375 3.24,4.583 0.479,0.208 10 false Starter 1.344,4.302 1.854,4.5 0.51,0.198 10 false Battery 6.125,0.771 6.458,0.969 0.333,0.198 10 false STA 4.688,2.26 4.938,2.438 0.25,0.177 10 false ST 6.344,4.708 6.667,4.906 0.323,0.198 10 false A57 6.344,4.875 6.74,5.073 0.396,0.198 10 false ECM 3.021,3.594 3.271,3.771 0.25,0.177 10 false ST 2.74,3.656 2.885,3.844 0.146,0.188 10 false B 2.396,3.667 2.698,3.865 0.302,0.198 10 false C11 2.969,3.385 3.271,3.583 0.302,0.198 10 false B99 2.469,3.479 2.615,3.667 0.146,0.188 10 false 1 2.927,3.167 3.073,3.354 0.146,0.188 10 false 1 4.448,1.781 4.594,1.969 0.146,0.188 10 false 1 4.458,2.729 4.604,2.917 0.146,0.188 10 false 2 4.01,1.792 4.156,1.979 0.146,0.188 10 false 5 4.01,2.729 4.156,2.917 0.146,0.188 10 false 3 5.906,0.667 6.115,0.865 0.208,0.198 10 false 6 3.219,0.677 3.365,0.865 0.146,0.188 10 false 9 1.823,0.667 2.031,0.865 0.208,0.198 10 false 12 2.125,0.677 2.542,0.875 0.417,0.198 10 false AM2 2.844,0.677 3.177,0.865 0.333,0.188 10 false ST2 1.813,1.094 2.125,1.281 0.313,0.188 10 false J63 1.823,1.26 3.469,1.469 1.646,0.208 10 false Ignition Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:
·

The following troubleshooting flowchart is based on the premise that the engine is cranked normally. If the engine does not crank, proceed to the problem symptoms table (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the value displayed on the GTS when the ignition switch is turned to ON and START position.

OK:
Ignition Switch Position GTS Display
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT IGNITION SWITCH ASSEMBLY
2.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (Click hereEngine / Hybrid System>N04C-VL (STARTING)>IGNITION SWITCH>INSPECTION).


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY - IGNITION SWITCH ASSEMBLY)
a.

Remove the STARTER relay from the No. 2 relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Disconnect the ignition switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Ignition Switch Position Specified Condition
ST relay terminal 1 or A57-6 (STA) - Body ground Always 10 kΩ or higher
J63-9 (ST2) or A57-6 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STARTER RELAY - IGNITION SWITCH ASSEMBLY)