Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for 2 Connectors Type)
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0357115 AIRBAG SYSTEM(for 2 Connectors Type) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for 2 Connectors Type)  B161B/1A  Front Center Airbag Sensor  


DESCRIPTION

The front airbag sensor consists of a diagnostic circuit, frontal deceleration sensor, etc.

If the airbag ECU assembly receives signals from the frontal deceleration sensor, it determines whether the SRS should be activated.

DTC B161B/1A is stored when a malfunction is detected in the front airbag sensor circuit.

DTC Code DTC Detection Condition Trouble Area
B161B/1A Either condition is met:
·

A front airbag sensor malfunction.

·

An airbag ECU assembly malfunction.


·

Front airbag sensor

·

Airbag ECU assembly



WIRING DIAGRAM

C116435E12
1.354,0.885 1.75,1.083 0.396,0.198 10 false +SL 1.365,2.073 1.719,2.281 0.354,0.208 10 false -SL 5.594,0.906 5.99,1.104 0.396,0.198 10 false +SL 5.594,2.052 5.948,2.26 0.354,0.208 10 false -SL 1.729,0.802 2.021,0.99 0.292,0.188 10 false 2 3.563,0.708 3.854,0.896 0.292,0.188 10 false 2 5.313,0.813 5.604,1 0.292,0.188 10 false 30 1.719,1.979 2.01,2.167 0.292,0.188 10 false 1 3.573,1.875 3.865,2.063 0.292,0.188 10 false 1 3.49,1.104 3.885,1.302 0.396,0.198 10 false +SL 3.531,2.281 3.885,2.49 0.354,0.208 10 false -SL 3.5,0.917 3.896,1.115 0.396,0.198 10 false AF1 3.51,2.083 3.906,2.281 0.396,0.198 10 false AF1 5.313,1.979 5.604,2.167 0.292,0.188 10 false 28 0.417,2.792 0.813,3 0.396,0.208 10 false F10 0.406,2.979 1.833,3.177 1.427,0.198 10 false Front Airbag Sensor 5.479,2.771 5.875,2.979 0.396,0.208 10 false A58 5.469,2.958 7.052,3.167 1.583,0.208 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After replacing the airbag ECU assembly, refer to initialization (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, wiggle each connector of the airbag system or drive the vehicle on various types of roads (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT AIRBAG SENSOR
a.
C238767E02
0.896,1.375 1.208,1.573 0.313,0.198 10 false *1 2.302,1.375 2.615,1.573 0.313,0.198 10 false *2

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


c.

Temporarily replace the front airbag sensor with a new one (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT AIRBAG SENSOR>REMOVAL).


d.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.


e.

Turn the ignition switch to ON, and wait at least 60 seconds.



g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait at least 60 seconds.


i.

Check for DTCs (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>DTC CHECK / CLEAR).

OK:

DTC B161B/1A is not output.


HINT:

Codes other than DTC B161B/1A may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Airbag Sensor
*2 Airbag ECU Assembly


Result:
Proceed to
OK
NG



OK

END (FRONT AIRBAG SENSOR WAS DEFECTIVE)

NG