Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for 2 Connectors Type)
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0357115 AIRBAG SYSTEM(for 2 Connectors Type) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for 2 Connectors Type)  B161C/9A  Lost Communication with Front Satellite Sensor Bus Center  B161D/9A  Front Satellite Sensor Bus Center Initialization Incomplete  


DESCRIPTION

The front airbag sensor circuit consists of the airbag ECU assembly and front airbag sensor.

The front airbag sensor detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbag should be deployed.

DTC B161C/9A or B161D/9A is stored when a malfunction is detected in the front airbag sensor circuit.

DTC Code DTC Detection Condition Trouble Area
B161C/9A
B161D/9A
One of the following conditions is met:
·

The airbag ECU assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor circuit for 2 seconds.

·

A front airbag sensor malfunction.

·

An airbag ECU assembly malfunction.


·

Engine room main wire

·

Cowl wire

·

Front airbag sensor

·

Airbag ECU assembly



WIRING DIAGRAM

C116435E12
1.354,0.885 1.75,1.083 0.396,0.198 10 false +SL 1.365,2.073 1.719,2.281 0.354,0.208 10 false -SL 5.594,0.906 5.99,1.104 0.396,0.198 10 false +SL 5.594,2.052 5.948,2.26 0.354,0.208 10 false -SL 1.729,0.802 2.021,0.99 0.292,0.188 10 false 2 3.563,0.708 3.854,0.896 0.292,0.188 10 false 2 5.313,0.813 5.604,1 0.292,0.188 10 false 30 1.719,1.979 2.01,2.167 0.292,0.188 10 false 1 3.573,1.875 3.865,2.063 0.292,0.188 10 false 1 3.49,1.104 3.885,1.302 0.396,0.198 10 false +SL 3.531,2.281 3.885,2.49 0.354,0.208 10 false -SL 3.5,0.917 3.896,1.115 0.396,0.198 10 false AF1 3.51,2.083 3.906,2.281 0.396,0.198 10 false AF1 5.313,1.979 5.604,2.167 0.292,0.188 10 false 28 0.417,2.792 0.813,3 0.396,0.208 10 false F10 0.406,2.979 1.833,3.177 1.427,0.198 10 false Front Airbag Sensor 5.479,2.771 5.875,2.979 0.396,0.208 10 false A58 5.469,2.958 7.052,3.167 1.583,0.208 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After replacing the airbag ECU assembly, refer to initialization (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag ECU assembly and front airbag sensor.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.
C373331E01
0.708,1.375 1.021,1.573 0.313,0.198 10 false *1 2.313,1.375 2.625,1.573 0.313,0.198 10 false *4 1.229,0.813 1.479,0.99 0.25,0.177 10 false *2 1.635,0.792 1.885,0.969 0.25,0.177 10 false *3

Disconnect the connectors from the airbag ECU assembly, front airbag sensor, cowl wire and engine room main wire.


b.

Check that the connectors (on both sides of cowl wire and engine room main wire) are not damaged.

OK:

The connectors are not deformed or damaged.


Text in Illustration
*1 Front Airbag Sensor
*2 Cowl Wire
*3 Engine Room Main Wire
*4 Airbag ECU Assembly


Result:
Proceed to
OK
NG



OK

3.CHECK FRONT AIRBAG SENSOR

NG

REPLACE ENGINE ROOM MAIN WIRE OR COWL WIRE

3.CHECK FRONT AIRBAG SENSOR
a.

Connect the connector to the cowl wire and engine room main wire.


b.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.

C373204E01
2.667,0.688 3.083,0.906 0.417,0.219 4.938,0.75 5.354,0.969 0.417,0.219 3.146,1.365 3.281,1.365 3.281,1.365 3.51,0.885 true 4.031,1.354 3.854,1.354 3.854,1.354 3.688,0.875 true 5.25,0.542 5.385,0.542 5.385,0.542 5.615,0.875 true 6.552,0.51 6.323,0.51 6.323,0.51 5.833,0.875 true 5.333,1.531 5.469,1.531 5.469,1.531 5.604,1.333 true 0.677,0.875 0.833,1.073 0.156,0.198 10 false F 1.615,0.875 1.771,1.073 0.156,0.198 10 false A 0.604,1.177 0.865,1.365 0.26,0.188 10 false *1 1.698,1.188 1.938,1.385 0.24,0.198 10 false *2 0.927,1.073 1.167,1.271 0.24,0.198 10 false E 1.083,1.073 1.323,1.271 0.24,0.198 10 false D 1.208,1.073 1.448,1.271 0.24,0.198 10 false C 1.344,1.073 1.583,1.271 0.24,0.198 10 false B 2.854,0.083 3.094,0.281 0.24,0.198 10 false *a 5.073,0.083 5.313,0.281 0.24,0.198 10 false *b 3.49,0.271 3.729,0.469 0.24,0.198 10 false *3 5.938,0.146 6.177,0.344 0.24,0.198 10 false *4 2.75,0.708 3.083,0.906 0.333,0.198 10 false F10 2.698,1.26 3.25,1.458 0.552,0.198 10 false 1 (-SL) 4.073,1.281 4.667,1.49 0.594,0.208 10 false 2 (+SL) 4.688,0.479 5.281,0.688 0.594,0.208 10 false 30 (+SL) 5.021,0.771 5.479,0.979 0.458,0.208 10 false A58 5.177,1.448 5.458,1.646 0.281,0.198 10 false *5 6.583,0.438 7.135,0.625 0.552,0.188 10 false 28 (-SL)

Text in Illustration
*1 Front Airbag Sensor *2 Airbag ECU Assembly
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Front Airbag Sensor)
*b Rear view of wire harness connector
(to Airbag ECU Assembly)


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F10-2 (+SL) - Body ground Ignition switch ON Below 1 V
F10-1 (-SL) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


g.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F10-2 (+SL) - F10-1 (-SL) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F10-2 (+SL) - F10-1 (-SL) Always 1 MΩ or higher
F10-2 (+SL) - Body ground Always 1 MΩ or higher
F10-1 (-SL) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT AIRBAG SENSOR

NG

5.CHECK ENGINE ROOM MAIN WIRE
4.CHECK FRONT AIRBAG SENSOR
a.
C238767E02
0.896,1.375 1.208,1.573 0.313,0.198 10 false *1 2.302,1.375 2.615,1.573 0.313,0.198 10 false *2

Connect the connector to the airbag ECU assembly.


b.

Temporarily replace the front airbag sensor with a new one (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT AIRBAG SENSOR>REMOVAL).


c.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.


d.

Turn the ignition switch to ON, and wait at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait at least 60 seconds.


h.

Check for DTCs (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>DTC CHECK / CLEAR).

OK:

DTC B161C/9A and B161D/9A are not output.


HINT:

Codes other than DTCs B161C/9A and B161D/9A may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Airbag Sensor
*2 Airbag ECU Assembly


Result:
Proceed to
OK
NG



OK

END (FRONT AIRBAG SENSOR WAS DEFECTIVE)

NG

5.CHECK ENGINE ROOM MAIN WIRE
a.

Disconnect the engine room main wire connector from the cowl wire.

C372838E01
2.688,0.729 3.135,0.958 0.448,0.229 4.99,0.792 5.438,1.021 0.448,0.229 3.115,1.417 3.292,1.417 3.292,1.417 3.458,0.938 true 4.063,1.427 3.854,1.427 3.854,1.427 3.688,0.927 true 5.281,1.302 5.448,1.302 5.448,1.302 5.656,1.063 true 5.427,1.615 5.594,1.615 5.594,1.615 5.688,1.469 false 6.458,1.365 6.292,1.365 6.292,1.365 5.885,1.073 true 0.469,0.875 0.677,1.073 0.208,0.198 10 false F 0.75,1.094 0.958,1.292 0.208,0.198 10 false E 1,1.094 1.208,1.292 0.208,0.198 10 false D 1.188,1.094 1.396,1.292 0.208,0.198 10 false C 1.458,1.094 1.667,1.292 0.208,0.198 10 false B 1.75,0.896 1.958,1.094 0.208,0.198 10 false A 0.833,0.74 1.063,0.938 0.229,0.198 10 false *2 1.26,0.75 1.5,0.948 0.24,0.198 10 false *3 0.375,1.188 0.583,1.385 0.208,0.198 10 false *1 1.844,1.188 2.052,1.385 0.208,0.198 10 false *4 2.708,0.104 2.969,0.302 0.26,0.198 10 false *a 3.49,0.063 3.75,0.26 0.26,0.198 10 false *5 5.188,0.115 5.448,0.313 0.26,0.198 10 false *b 5.927,0.188 6.188,0.385 0.26,0.198 10 false *6 2.792,0.76 3.177,0.958 0.385,0.198 10 false AF1 5.083,0.823 5.469,1.021 0.385,0.198 10 false A58 2.667,1.323 3.25,1.521 0.583,0.198 10 false 1 (-SL) 4.719,1.208 5.302,1.406 0.583,0.198 10 false 30 (+SL) 4.104,1.344 4.688,1.542 0.583,0.198 10 false 2 (+SL) 5.281,1.542 5.563,1.74 0.281,0.198 10 false *7 6.531,1.281 7.146,1.469 0.615,0.188 10 false 28 (-SL)

Text in Illustration
*1 Front Airbag Sensor *2 Cowl Wire
*3 Engine Room Main Wire *4 Airbag ECU Assembly
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Cowl Wire)
*b Rear view of wire harness connector
(to Airbag ECU Assembly)


b.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
AF1-2 (+SL) - Body ground Ignition switch ON Below 1 V
AF1-1 (-SL) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


g.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF1-2 (+SL) - AF1-1 (-SL) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF1-2 (+SL) - AF1-1 (-SL) Always 1 MΩ or higher
AF1-2 (+SL) - Body ground Always 1 MΩ or higher
AF1-1 (-SL) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COWL WIRE

NG

REPLACE ENGINE ROOM MAIN WIRE