Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for 2 Connectors Type)
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0357115 AIRBAG SYSTEM(for 2 Connectors Type) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for 2 Connectors Type)  B1662/45  Indicator Light Circuit Malfunction  


DESCRIPTION

The SRS warning light is located on the combination meter assembly.

When the SRS warning light is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on or blinks* to inform the driver of the problem.

DTC B1662/45 is stored when a malfunction is detected in the SRS warning light circuit.

*: If the SRS warning light blinks, replace the airbag ECU assembly with a new one.


DTC Code DTC Detection Condition Trouble Area
B1662/45 One of the following conditions is met:
·

An airbag ECU assembly malfunction.

·

A combination meter assembly malfunction.


·

Combination meter assembly

·

Airbag ECU assembly



WIRING DIAGRAM

C373213E01
0.083,0.333 1.542,0.542 1.458,0.208 10 false from IG2-NO.2 Relay 1.771,1.24 2.771,1.448 1,0.208 10 false METER-IG2 2.729,2.073 4.698,2.292 1.969,0.219 10 false Combination Meter Assembly 2.74,1.885 3.021,2.083 0.281,0.198 10 false J1 2.74,1.448 3.021,1.646 0.281,0.198 10 false 21 2.771,0.979 3.052,1.177 0.281,0.198 10 false 2 2.979,1.083 3.323,1.271 0.344,0.188 10 false IG+ 2.979,1.563 3.323,1.75 0.344,0.188 10 false ES 4.135,1.094 4.479,1.281 0.344,0.188 10 false A/B 3.24,0.5 4.24,0.708 1,0.208 10 false A/BAG-IG2 4.51,0.969 4.792,1.167 0.281,0.198 10 false 40 5.323,0.229 5.604,0.427 0.281,0.198 10 false 21 5.333,0.979 5.615,1.177 0.281,0.198 10 false 14 5.323,1.75 5.604,1.948 0.281,0.198 10 false 25 5.333,2.229 5.708,2.427 0.375,0.198 10 false A58 5.344,2.417 6.938,2.625 1.594,0.208 10 false Airbag ECU Assembly 5.604,0.365 5.979,0.563 0.375,0.198 10 false IG2 5.604,1.073 5.979,1.271 0.375,0.198 10 false LA 5.594,1.865 5.969,2.063 0.375,0.198 10 false E1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After replacing the airbag ECU assembly, refer to initialization (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag ECU assembly and combination meter assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.
C239134E02
0.906,1.375 1.219,1.573 0.313,0.198 10 false *1 2.281,1.375 2.594,1.573 0.313,0.198 10 false *2

Disconnect the connectors from the airbag ECU assembly and combination meter assembly.


b.

Check that the connectors (on the airbag ECU assembly side and combination meter assembly side) are not damaged.

OK:

The connectors are not deformed or damaged.


Text in Illustration
*1 Combination Meter Assembly
*2 Airbag ECU Assembly


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

C373327E01
2.521,0.583 2.938,0.813 0.417,0.229 4.469,0.823 4.885,1.052 0.417,0.229 3.125,1.458 3.292,1.458 3.292,1.458 3.781,0.875 true 6.167,1.448 6.333,1.448 6.333,1.448 6.75,1.042 true 0.656,0.906 0.969,1.104 0.313,0.198 10 false D 0.573,1.26 0.885,1.458 0.313,0.198 10 false *1 1.938,1.271 2.25,1.469 0.313,0.198 10 false *2 1,1.125 1.24,1.323 0.24,0.198 10 false C 1.458,1.125 1.698,1.323 0.24,0.198 10 false B 1.75,0.917 1.99,1.115 0.24,0.198 10 false A 2.563,0.094 2.927,0.302 0.365,0.208 10 false *a 2.615,0.615 2.979,0.823 0.365,0.208 10 false A58 4.708,0.135 5.073,0.344 0.365,0.208 10 false *b 5.802,0.333 6.167,0.542 0.365,0.208 10 false *4 4.615,0.854 4.979,1.063 0.365,0.208 10 false J1 2.646,1.365 3.229,1.573 0.583,0.208 10 false 14 (LA) 5.635,1.344 6.26,1.552 0.625,0.208 10 false 40 (A/B) 3.552,0.125 3.917,0.333 0.365,0.208 10 false *3

Text in Illustration
*1 Combination Meter Assembly *2 Airbag ECU Assembly
*3 Connector B *4 Connector C
*a Rear view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Combination Meter Assembly)

Standard Resistance:
Tester Connection Condition Specified Condition
A58-14 (LA) - J1-40 (A/B) Always Below 1 Ω
A58-14 (LA) - Body ground Always 1 MΩ or higher
J1-40 (A/B) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK COMBINATION METER ASSEMBLY

NG

REPLACE HARNESS AND CONNECTOR

4.CHECK COMBINATION METER ASSEMBLY
a.

Connect the connector to the combination meter assembly.

C373328E01
3.906,0.51 4.365,0.75 0.458,0.24 4.563,1.521 4.771,1.521 4.771,1.521 5.125,1.26 true 5.552,1.49 5.365,1.49 5.365,1.49 5.198,1.063 true 5.958,1.25 5.802,1.25 5.802,1.25 5.25,0.865 true 0.802,1.26 1.115,1.458 0.313,0.198 10 false *1 1.698,1.156 1.938,1.354 0.24,0.198 10 false B 2,0.906 2.24,1.115 0.24,0.208 10 false A 2.146,1.26 2.385,1.469 0.24,0.208 10 false *2 3.615,0.177 3.906,0.385 0.292,0.208 10 false *a 5.042,0.146 5.333,0.354 0.292,0.208 10 false *3 4.01,0.552 4.375,0.729 0.365,0.177 10 false A58 4.375,1.448 4.667,1.615 0.292,0.167 10 false *4 5.594,1.417 6.167,1.604 0.573,0.188 10 false 25 (E1) 5.99,1.167 6.563,1.354 0.573,0.188 10 false 14 (LA) 0.896,0.906 1.208,1.104 0.313,0.198 10 false D

Text in Illustration
*1 Combination Meter Assembly *2 Airbag ECU Assembly
*3 Connector B *4 Service Wire
*a Rear view of wire harness connector
(to Airbag ECU Assembly)
- -


b.

Using a service wire, connect terminals 14 (LA) and 25 (E1) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



c.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.


d.

Turn the ignition switch to ON.


e.

Check the SRS warning light condition.

OK:

The SRS warning light is not illuminated.



f.

Turn the ignition switch off.


g.

Disconnect the service wire from connector B.


h.

Turn the ignition switch to ON.


i.

Check the SRS warning light condition.

OK:

The SRS warning light is illuminated.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY