Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for 2 Connectors Type)
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0357115 AIRBAG SYSTEM(for 2 Connectors Type) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for 2 Connectors Type)  B1905/74  Short in Front Pretensioner Squib LH Circuit  B1906/74  Open in Front Pretensioner Squib LH Circuit  B1907/74  Short to GND in Front Pretensioner Squib LH Circuit  B1908/74  Short to B+ in Front Pretensioner Squib LH Circuit  


DESCRIPTION

The front pretensioner squib LH circuit consists of the airbag ECU assembly and front seat outer belt assembly LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1905/74 One of the following conditions is met:
·

The airbag ECU assembly detects a line short circuit signal 5 times in the front pretensioner squib LH circuit during the primary check.

·

A front pretensioner squib LH malfunction.

·

An airbag ECU assembly malfunction.


·

Engine room main wire

·

Front seat outer belt assembly LH

·

Airbag ECU assembly


B1906/74 One of the following conditions is met:
·

The airbag ECU assembly detects an open circuit signal in the front pretensioner squib LH circuit for 2 seconds.

·

A front pretensioner squib LH malfunction.

·

An airbag ECU assembly malfunction.


B1907/74 One of the following conditions is met:
·

The airbag ECU assembly detects a short circuit to ground signal in the front pretensioner squib LH circuit for 0.5 seconds.

·

A front pretensioner squib LH malfunction.

·

An airbag ECU assembly malfunction.


B1908/74 One of the following conditions is met:
·

The airbag ECU assembly detects a short circuit to B+ signal in the front pretensioner squib LH circuit for 0.5 seconds.

·

A front pretensioner squib LH malfunction.

·

An airbag ECU assembly malfunction.



WIRING DIAGRAM

C401363E02
1.438,0.365 1.75,0.563 0.313,0.198 10 false L+ 1.469,1.115 1.781,1.313 0.313,0.198 10 false L- 1.708,0.365 2.021,0.563 0.313,0.198 10 false 1 1.74,1.125 2.052,1.323 0.313,0.198 10 false 2 5.365,0.365 5.677,0.563 0.313,0.198 10 false 5 5.385,1.125 5.698,1.323 0.313,0.198 10 false 4 5.573,0.469 5.99,0.677 0.417,0.208 10 false PL+ 5.594,1.24 6.01,1.448 0.417,0.208 10 false PL- 0.385,1.74 0.833,1.948 0.448,0.208 10 false A69 0.385,1.906 2.865,2.125 2.479,0.219 10 false Front Seat Outer Belt Assembly LH 5.354,1.917 7.104,2.167 1.75,0.25 10 false Airbag ECU Assembly 5.354,1.74 5.802,1.948 0.448,0.208 10 false A59

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After replacing the airbag ECU assembly, refer to initialization (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH
a.

Turn the ignition switch off.

C373205E02
4.104,0.74 4.531,1 0.427,0.26 4.573,0.385 4.76,0.385 4.76,0.385 5.01,0.615 true 5.49,0.396 5.323,0.396 5.323,0.396 5.094,0.615 true 5.74,1.031 5.573,1.031 5.573,1.031 5.333,0.813 true 1.104,0.74 1.417,0.938 0.313,0.198 10 false *1 1.479,0.938 1.792,1.135 0.313,0.198 10 false D 1.76,0.948 2.073,1.146 0.313,0.198 10 false C 2.323,0.75 2.635,0.948 0.313,0.198 10 false A 2.427,1.26 2.74,1.458 0.313,0.198 10 false *2 3.906,0.125 4.219,0.323 0.313,0.198 10 false *a 4.167,0.313 4.625,0.521 0.458,0.208 10 false 1 (L+) 5.531,0.323 5.99,0.531 0.458,0.208 10 false 2 (L-) 4.958,0.177 5.271,0.375 0.313,0.198 10 false *3 4.198,0.781 4.573,0.979 0.375,0.198 10 false A69 5.781,0.948 6.156,1.146 0.375,0.198 10 false *4

Text in Illustration
*1 Front Seat Outer Belt Assembly LH *2 Airbag ECU Assembly
*3 Connector C *4 SST
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)
- -


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front seat outer belt assembly LH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>DTC CHECK / CLEAR).

OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTC B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector C.


Result:
Proceed to
OK
NG



OK

NG

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.
C373206E01
0.51,0.771 0.823,0.969 0.313,0.198 10 false *1 1.042,0.969 1.354,1.167 0.313,0.198 10 false D 1.25,0.969 1.563,1.167 0.313,0.198 10 false C 1.427,0.615 1.74,0.813 0.313,0.198 10 false *3 1.75,0.979 2.063,1.177 0.313,0.198 10 false B 2.083,0.792 2.396,0.99 0.313,0.198 10 false A 2.25,1.396 2.563,1.594 0.313,0.198 10 false *2

Disconnect the connectors from the airbag ECU assembly.


b.

Check that the connectors (on the airbag ECU assembly side and front seat outer belt assembly LH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Text in Illustration
*1 Front Seat Outer Belt Assembly LH
*2 Airbag ECU Assembly
*3 Engine Room Main Wire


Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE ROOM MAIN WIRE

NG

REPLACE ENGINE ROOM MAIN WIRE

3.CHECK ENGINE ROOM MAIN WIRE
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C373207E02
4.125,0.583 4.542,0.823 0.417,0.24 5.458,0.406 5.302,0.406 5.302,0.406 5.115,0.615 true 4.615,0.385 4.792,0.385 4.792,0.385 5.01,0.625 true 0.927,0.75 1.24,0.948 0.313,0.198 10 false *1 1.323,0.938 1.635,1.135 0.313,0.198 10 false D 1.552,0.938 1.865,1.135 0.313,0.198 10 false C 1.979,0.938 2.292,1.135 0.313,0.198 10 false B 1.729,0.594 2.042,0.792 0.313,0.198 10 false *3 2.313,0.75 2.625,0.948 0.313,0.198 10 false A 2.438,1.24 2.75,1.438 0.313,0.198 10 false *2 3.833,0.073 4.146,0.271 0.313,0.198 10 false *a 4.958,0.188 5.271,0.385 0.313,0.198 10 false *4 4.229,0.302 4.708,0.51 0.479,0.208 10 false 1 (L+) 5.479,0.323 5.948,0.531 0.469,0.208 10 false 2 (L-) 4.208,0.615 4.688,0.823 0.479,0.208 10 false A69

Text in Illustration
*1 Front Seat Outer Belt Assembly LH *2 Airbag ECU Assembly
*3 Engine Room Main Wire *4 Connector C
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)
- -


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A69-1 (L+) - Body ground Ignition switch ON Below 1 V
A69-2 (L-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A69-1 (L+) - A69-2 (L-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A69-1 (L+) - A69-2 (L-) Always 1 MΩ or higher
A69-1 (L+) - Body ground Always 1 MΩ or higher
A69-2 (L-) - Body ground Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

4.CHECK FOR DTC

NG

REPLACE ENGINE ROOM MAIN WIRE

4.CHECK FOR DTC
a.
C373208E01
0.625,0.875 0.938,1.073 0.313,0.198 10 false *1 1.083,1.063 1.396,1.26 0.313,0.198 10 false D 1.219,1.063 1.531,1.26 0.313,0.198 10 false C 1.823,0.844 2.135,1.042 0.313,0.198 10 false A 1.99,1.469 2.302,1.667 0.313,0.198 10 false *2

Connect the connectors to the front seat outer belt assembly LH and airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>DTC CHECK / CLEAR).

OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTC B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Outer Belt Assembly LH
*2 Airbag ECU Assembly


Result:
Proceed to
OK
NG



OK

NG