Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for 3 Connectors Type) › 2017.01–2019.08
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0357116 AIRBAG SYSTEM(for 3 Connectors Type) J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for 3 Connectors Type)  Diagnosis Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are output by the blinking of the SRS warning light.

HINT:
·

When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU, including the airbag sensor assembly. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.



WIRING DIAGRAM

C377017E01
1.792,1.813 2.104,2.01 0.313,0.198 10 false TC 2.073,1.698 2.385,1.896 0.313,0.198 10 false 17 1.25,2.573 1.625,2.771 0.375,0.198 10 false A53 1.24,2.771 1.667,2.958 0.427,0.188 10 false ECM 1.083,3.583 1.385,3.771 0.302,0.188 10 false 4 1.302,3.708 1.656,3.896 0.354,0.188 10 false CG 1.802,3.719 2.156,3.906 0.354,0.188 10 false TC 2.094,3.594 2.448,3.781 0.354,0.188 10 false 13 1.26,4.24 1.615,4.427 0.354,0.188 10 false J45 1.26,4.438 1.781,4.625 0.521,0.188 10 false DLC3 5.438,4.74 5.906,4.927 0.469,0.188 10 false A58 5.438,4.938 7.104,5.125 1.667,0.188 10 false Airbag Sensor Assembly 0.615,5.24 2.521,5.427 1.906,0.188 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the airbag ECU assembly, refer to initialization (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).


Result:
Result Proceed to
DTC is not output A
DTCs are output B



A

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)

B

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
a.

Turn the ignition switch off.

C377018E01
1.708,0.729 2.198,0.99 0.49,0.26 4.927,0.563 5.417,0.823 0.49,0.26 2.417,2.167 2.188,2.167 2.188,2.167 1.99,1.708 true 5.125,2.219 4.958,2.219 4.958,2.219 4.76,1.677 true 3.781,0.563 4.094,0.76 0.313,0.198 10 false *b 0.802,0.542 1.115,0.74 0.313,0.198 10 false *a 1.844,0.771 2.177,0.969 0.333,0.198 10 false J45 5.052,0.604 5.438,0.802 0.385,0.198 10 false A53 2.448,2.094 2.781,2.292 0.333,0.198 10 false TC 5.177,2.125 5.51,2.323 0.333,0.198 10 false TC

Text in Illustration
*a Front view of DLC3 *b Front view of wire harness connector
(to ECM)


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J45-13 (TC) - A53-17 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.
C198509E32
1.448,0.24 1.875,0.49 0.427,0.25 1.042,0.365 1.229,0.365 1.229,0.365 1.542,0.917 true 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 0.781,0.281 1.094,0.479 0.313,0.198 10 false CG 1.542,0.271 1.854,0.469 0.313,0.198 10 false J45

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J45-4 (CG) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of DLC3


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.
C377019E01
1.5,0.167 1.958,0.396 0.458,0.229 0.74,1.719 0.917,1.719 0.917,1.719 1.156,1.302 true 0.208,0.104 0.521,0.302 0.313,0.198 10 false *a 1.594,0.198 1.99,0.396 0.396,0.198 10 false A53 0.51,1.646 0.844,1.854 0.333,0.208 10 false TC

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A53-17 (TC) - Body ground Always 1 MΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU