Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0104  Mass or Volume Air Flow Sensor "A" Circuit Intermittent  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0104 Mass or Volume Air Flow Sensor "A" Circuit Intermittent Diagnosis condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction status:

The condition that the output of the mass air flow meter is less than 0.85 kHz remains for 3 seconds or more, or the condition that the output of the mass air flow meter is greater than 9.8 kHz remains for 3 seconds or more.


Malfunction duration:

3 seconds or more


·

Mass air flow meter

·

Harness or connector

·

ECM


Class A DTC stored

MONITOR DESCRIPTION

The mass air flow meter installed to the air cleaner consistently measures an intake air volume.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0104 Ignition switch ON for 3 seconds or more.


WIRING DIAGRAM

A450604E03
0.719,2.958 3.927,3.156 3.208,0.198 10 false Mass Air Flow Meter 0.75,2.781 1.677,2.99 0.927,0.208 10 false B51 5.781,2.948 6.375,3.208 0.594,0.26 10 false ECM 5,2.406 5.396,2.573 0.396,0.167 10 false B142 4.979,1.396 5.344,1.563 0.365,0.167 10 false A115 4.99,0.385 5.354,0.552 0.365,0.167 10 false B142 4.99,1.896 5.354,2.063 0.365,0.167 10 false B142 5.438,0.906 5.927,1.073 0.49,0.167 10 false E2 5.427,1.927 5.917,2.094 0.49,0.167 10 false EVG 5.406,0.438 5.896,0.604 0.49,0.167 10 false THA 5.427,1.438 5.917,1.604 0.49,0.167 10 false +B 5.094,2.24 5.458,2.406 0.365,0.167 10 false 81 5.104,0.198 5.469,0.365 0.365,0.167 10 false 3 5.083,1.25 5.448,1.417 0.365,0.167 10 false 49 5.094,1.74 5.458,1.906 0.365,0.167 10 false 91 1.656,2.438 2.146,2.604 0.49,0.167 10 false FG 1.594,1.927 2.083,2.094 0.49,0.167 10 false E2G 1.677,1.438 2.167,1.604 0.49,0.167 10 false +B 1.604,0.438 2.094,0.604 0.49,0.167 10 false THA 2,0.292 2.49,0.458 0.49,0.167 10 false 1 2,2.302 2.49,2.469 0.49,0.167 10 false 5 2.01,1.281 2.5,1.448 0.49,0.167 10 false 3 2.01,1.802 2.5,1.969 0.49,0.167 10 false 4 4.635,1.906 5,2.073 0.365,0.167 10 false E-57 4.667,1.396 5.031,1.563 0.365,0.167 10 false V-1 4.635,0.396 5,0.563 0.365,0.167 10 false E-47 4.635,2.406 5,2.573 0.365,0.167 10 false E-74 5.417,2.438 5.906,2.604 0.49,0.167 10 false VG 1.698,0.917 2.188,1.083 0.49,0.167 10 false E2 2.01,0.792 2.5,0.958 0.49,0.167 10 false 2 5,0.896 5.365,1.063 0.365,0.167 10 false B142 5.073,0.698 5.438,0.865 0.365,0.167 10 false 58 4.625,0.896 4.99,1.063 0.365,0.167 10 false M-32

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the mass air flow meter connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK INTAKE MASS AIR FLOW METER SUB-ASSEMBLY

NG

14.CONNECT SECURELY
2.CHECK INTAKE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Check the installation of the intake mass air flow meter sub-assembly.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the intake mass air flow meter sub-assembly.


Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

13.REPAIR OR REPLACE MASS AIR FLOW METER
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0104 is output A
DTC P0104 other DTCs is output B




A

4.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

B

4.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405886C08
1.49,0.094 1.896,0.375 0.406,0.281 0.281,0.167 0.594,0.365 0.313,0.198 10 false *a 1.625,0.156 1.938,0.354 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


A405887C04
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-1 - Body ground and other terminals Always 10 kΩ or higher
E-57 - Body ground and other terminals Always 10 kΩ or higher
E-74 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS OR CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS OR CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Disconnect the mass air flow meter connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A451192C10
0.385,0.948 0.802,1.24 0.417,0.292 1.01,1.813 1.667,1.125 true 1.885,1.813 1.854,1.125 true 2.625,1.823 1.979,1.115 true 0.469,1.01 0.927,1.208 0.458,0.198 10 false B51 0.896,1.854 1.354,2.052 0.458,0.198 10 false +B 1.802,1.875 2.26,2.073 0.458,0.198 10 false E2G 2.604,1.865 3.063,2.063 0.458,0.198 10 false FG 0.094,0.104 0.552,0.302 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Mass Air Flow Meter)


A405886C03
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


A405887C04
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-1 - B51-3 (+B) Always Below 1 Ω
E-57 - B51-4 (E2G) Always Below 1 Ω
E-74 - B51-5 (FG) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS OR CONNECTOR

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK HARNESS OR CONNECTOR
A451192C11
0.385,0.948 0.802,1.24 0.417,0.292 1.01,1.813 1.667,1.125 true 0.479,1.021 0.938,1.219 0.458,0.198 10 false B51 0.896,1.854 1.354,2.052 0.458,0.198 10 false +B 0.094,0.104 0.552,0.302 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Mass Air Flow Meter)


a.

Disconnect the mass air flow meter connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V-1 - B51-3 (+B) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG


A405886C03
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector



OK

7.CHECK MASS AIR FLOW METER

NG

10.REPLACE ECM
7.CHECK MASS AIR FLOW METER
a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.

Start the engine.


A405887C04
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness Lead Connector


d.

Measure the signal between the terminals and the ECM.

Standard:
Tester Connection Condition Specified Condition
E-74 - E-57 Ignition switch ON 1.8 to 2.2 kHz



Result:
Proceed to
OK
NG



OK

9.CHECK DTC OUTPUT

NG

8.REPLACE MASS AIR FLOW METER
8.REPLACE MASS AIR FLOW METER

Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
9.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0104 is output A
DTCs are not output B




A

10.REPLACE ECM

B

END

10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT
11.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT
13.REPAIR OR REPLACE MASS AIR FLOW METER
a.

Replace or replace the mass air flow meter.

HINT:

If damaged, replace the mass air flow meter.



Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT
14.CONNECT SECURELY
a.

Connect securely the mass air flow meter connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT