Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0128  Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0128 Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) Diagnosis Condition:
·

Engine speed 590 rpm or more

·

Engine coolant temperature at engine start-up 30°C (86°F) or less.

·

Estimate engine coolant temperature is 90°C (194°F) or more after running the engine for 60 seconds or more.


Malfunction Status:

The condition that the actual engine coolant temperature is less than 50°C (122°F) remains for 5 seconds or more.


Malfunction Duration:

5 seconds or more


·

Thermostat

·

Engine coolant temperature sensor


Class B1 DTC stored

MONITOR DESCRIPTION

·

The thermostat prevents coolant from flowing into the radiator when the engine coolant temperature is less than 82°C (179.6°F), in order to secure the engine warm up function. When the temperature rises above 82°C (179.6°F), the valve opens and allows coolant to flow into the radiator, thereby preventing the engine from overheating.

·

If the thermostat fails and the valve stays open, it is difficult for the engine coolant temperature to rise, so the exhaust components that work after the engine coolant temperature has reached a certain value (warm up) will not operate for a long time. The thermostat must therefore be diagnosed to see if it is working properly.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0128 Start the engine from less than coolant temperature 30°C and travel for a fixed time after warming up.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (ENGINE COOLANT TEMPERATURE SENSOR)
a.

Check the connector connection for the engine coolant temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK ENGINE COOLANT TEMPERATURE SENSOR

NG

10.CONNECT SECURELY
2.CHECK ENGINE COOLANT TEMPERATURE SENSOR
a.

Check the installation of the engine coolant temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the engine coolant temperature sensor.


Result:
Proceed to
OK
NG



OK

3.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

9.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
3.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

4.CHECK THERMOSTAT

NG

8.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
4.CHECK THERMOSTAT

Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT

NG

7.REPLACE THERMOSTAT
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0128 is output A
DTCs are not output B




A

6.REPLACE ECM

B

END

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT
7.REPLACE THERMOSTAT

Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT
8.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT
9.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Repair or replace the engine coolant temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the engine coolant temperature sensor.



Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT
10.CONNECT SECURELY
a.

Connect securely the engine coolant temperature sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT
11.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END