Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0200  Injector Circuit/Open  P0201  Cylinder 1 Injector "A" Circuit  P0202  Cylinder 2 Injector "A" Circuit  P0203  Cylinder 3 Injector "A" Circuit  P0204  Cylinder 4 Injector "A" Circuit  P0611  Fuel Injector Control Module Performance  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0200 Injector Circuit/Open Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

With the injector not operating


Malfunction Status:
·

Fuel injector driver charge circuit voltage higher than 61 V

·

Failure timer 0.384 seconds or more


Malfunction Duration:

0.384 seconds or more


·

ECM

·

Temporary operating error due to radio wave interference or noise.


Class A DTC stored
P0201 Cylinder 1 Injector "A" Circuit Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V

·

Elapse of at least 2 seconds after turn the ignition switch to ON

·

Starter is not in operation.

·

Malfunction about actuator of the injection does not occur.

·

Fuel injection activity request is in progress.


Malfunction Status:

The fuel injector driver charge circuit remains at 0 A until it reaches a threshold.

(Approximately 4 seconds at 600 rpm. This may vary depending on engine speed.)


Malfunction Duration:

4 seconds or more


·

Injector assembly

·

Harness or connector

·

ECM


Class A DTC stored
P0202 Cylinder 2 Injector "A" Circuit Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V

·

Elapse of at least 2 seconds after turn the ignition switch to ON

·

Starter is not in operation.

·

Malfunction about actuator of the injection does not occur.

·

Fuel injection activity request is in progress.


Malfunction Status:

The fuel injector driver charge circuit remains at 0 A until it reaches a threshold.

(Approximately 4 seconds at 600 rpm. This may vary depending on engine speed.)


Malfunction Duration:

4 seconds or more


·

Injector assembly

·

Harness or connector

·

ECM


Class A DTC stored
P0203 Cylinder 3 Injector "A" Circuit Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V

·

Elapse of at least 2 seconds after turn the ignition switch to ON

·

Starter is not in operation.

·

Malfunction about actuator of the injection does not occur.

·

Fuel injection activity request is in progress.


Malfunction Status:

The fuel injector driver charge circuit remains at 0 A until it reaches a threshold.

(Approximately 4 seconds at 600 rpm. This may vary depending on engine speed.)


Malfunction Duration:

4 seconds or more


·

Injector assembly

·

Harness or connector

·

ECM


Class A DTC stored
P0204 Cylinder 4 Injector "A" Circuit Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V

·

Elapse of at least 2 seconds after turn the ignition switch to ON

·

Starter is not in operation.

·

Malfunction about actuator of the injection does not occur.

·

Fuel injection activity request is in progress.


Malfunction Status:

The fuel injector driver charge circuit remains at 0 A until it reaches a threshold.

(Approximately 4 seconds at 600 rpm. This may vary depending on engine speed.)


Malfunction Duration:

4 seconds or more


·

Injector assembly

·

Harness or connector

·

ECM


Class A DTC stored
P0611 Fuel Injector Control Module Performance Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

With the injector not operating


Malfunction Status:

Injector driver charge circuit voltage remains at 55 V or less for 0.1 seconds or more.


Malfunction Duration:

0.1 seconds or more


·

ECM

·

Temporary operating error due to radio wave interference or noise.


Class A DTC stored

MONITOR DESCRIPTION

P0201, P0202, P0203, P0204:

·

An injection quantity is controlled to a valve opening duration of the injector assembly.

·

The valve opening duration of the injector assembly is adjusted by the solenoid valve.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0200
P0611
Ignition switch ON for 1 seconds or more.
P0201
P0202
P0203
P0204
Idling for 6 seconds or more.


WIRING DIAGRAM

A407165E03
4.896,0.427 5.292,0.656 0.396,0.229 10 false B142 0.74,0.896 2.344,1.094 1.604,0.198 10 false No. 1 Injector Assembly 0.75,0.698 1.083,0.896 0.333,0.198 10 false i5 0.74,2 1.073,2.198 0.333,0.198 10 false i8 0.75,2.177 2.281,2.375 1.531,0.198 10 false No. 4 Injector Assembly 0.729,3.375 1.063,3.573 0.333,0.198 10 false i6 0.729,4.698 1.063,4.896 0.333,0.198 10 false i7 0.729,3.552 2.26,3.75 1.531,0.198 10 false No. 2 Injector Assembly 0.74,4.875 2.271,5.073 1.531,0.198 10 false No. 3 Injector Assembly 2.26,5.323 2.583,5.5 0.323,0.177 10 false Bi1 3.365,0.271 3.688,0.448 0.323,0.177 10 false * 3.365,1.615 3.688,1.792 0.323,0.177 10 false * 3.365,2.938 3.688,3.115 0.323,0.177 10 false * 3.354,4.302 3.677,4.479 0.323,0.177 10 false * 0.49,5.719 2.021,5.938 1.531,0.219 10 false *: Shield 5.333,0.865 5.667,1.063 0.333,0.198 10 false IJ1+ 5.333,1.323 5.667,1.521 0.333,0.198 10 false IJ3+ 5.323,0.448 5.656,0.646 0.333,0.198 10 false #1 5.323,1.719 5.656,1.917 0.333,0.198 10 false #3 5.323,3.573 5.656,3.771 0.333,0.198 10 false IJ2+ 5.323,4.01 5.656,4.208 0.333,0.198 10 false IJ4+ 4.979,1.104 5.313,1.302 0.333,0.198 10 false 54 5.323,4.438 5.656,4.635 0.333,0.198 10 false #2 5.813,6.115 6.385,6.354 0.573,0.24 10 false ECM 4.99,1.531 5.323,1.729 0.333,0.198 10 false 32 4.969,0.646 5.302,0.844 0.333,0.198 10 false 53 4.979,0.208 5.313,0.406 0.333,0.198 10 false 31 4.948,4.198 5.281,4.396 0.333,0.198 10 false 101 4.979,3.76 5.313,3.958 0.333,0.198 10 false 78 4.948,3.323 5.281,3.521 0.333,0.198 10 false 100 4.979,2.917 5.313,3.115 0.333,0.198 10 false 79 5.333,3.135 5.667,3.333 0.333,0.198 10 false #4 2.313,2.885 2.646,3.083 0.333,0.198 10 false 3 2.313,3.771 2.646,3.969 0.333,0.198 10 false 4 2.302,4.208 2.635,4.406 0.333,0.198 10 false 5 2.302,5.104 2.635,5.302 0.333,0.198 10 false 6 2.323,2.427 2.656,2.625 0.333,0.198 10 false 8 2.323,1.521 2.656,1.719 0.333,0.198 10 false 7 2.323,1.094 2.656,1.292 0.333,0.198 10 false 2 2.333,0.198 2.667,0.396 0.333,0.198 10 false 1 4.542,3.083 4.865,3.26 0.323,0.177 10 false E-20 4.542,3.979 4.865,4.156 0.323,0.177 10 false E-38 4.542,4.427 4.865,4.604 0.323,0.177 10 false E-19 4.542,3.521 4.865,3.698 0.323,0.177 10 false E-18 4.552,1.719 4.875,1.896 0.323,0.177 10 false E-16 4.552,1.313 4.875,1.49 0.323,0.177 10 false E-34 4.552,0.844 4.875,1.021 0.323,0.177 10 false E-14 4.552,0.406 4.875,0.583 0.323,0.177 10 false E-15 4.979,5.417 5.313,5.615 0.333,0.198 10 false 70 4.542,5.615 4.865,5.792 0.323,0.177 10 false E-55 5.302,5.635 5.635,5.833 0.333,0.198 10 false S 1.844,0.333 2.177,0.531 0.333,0.198 10 false 1 1.854,1.635 2.188,1.833 0.333,0.198 10 false 1 0.604,3 0.938,3.198 0.333,0.198 10 false 1 0.583,4.292 0.917,4.49 0.333,0.198 10 false 1 0.583,0.333 0.917,0.531 0.333,0.198 10 false 2 0.594,1.635 0.927,1.833 0.333,0.198 10 false 2 1.844,2.979 2.177,3.177 0.333,0.198 10 false 2 1.833,4.271 2.167,4.469 0.333,0.198 10 false 2 2.26,4.417 2.583,4.594 0.323,0.177 10 false Bi1 2.271,3.99 2.594,4.167 0.323,0.177 10 false Bi1 2.271,3.094 2.594,3.271 0.323,0.177 10 false Bi1 2.26,2.646 2.583,2.823 0.323,0.177 10 false Bi1 2.271,1.74 2.594,1.917 0.323,0.177 10 false Bi1 2.26,1.313 2.583,1.49 0.323,0.177 10 false Bi1 2.26,0.417 2.583,0.594 0.323,0.177 10 false Bi1 4.906,0.865 5.302,1.094 0.396,0.229 10 false B142 4.896,1.313 5.292,1.542 0.396,0.229 10 false B142 4.906,1.74 5.302,1.969 0.396,0.229 10 false B142 4.896,3.094 5.292,3.323 0.396,0.229 10 false B142 4.896,3.531 5.292,3.76 0.396,0.229 10 false B142 4.906,3.99 5.302,4.219 0.396,0.229 10 false B142 4.896,4.406 5.292,4.635 0.396,0.229 10 false B142 4.896,5.615 5.292,5.844 0.396,0.229 10 false B142

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration(Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS to ON.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC P0200 or P0611 is output A
DTC P0201, P0202, P0203 or P0204 is output B
P2146 or P2149 is output C



A

2.CHECK DTC OUTPUT

B

4.CHECK CONNECTOR CONNECTION CONDITION (ECM, INJECTOR ASSEMBLY CONNECTOR)

C

2.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0200 or P0611 is output A
DTCs are not output B




A

3.REPLACE ECM

B

END

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
4.CHECK CONNECTOR CONNECTION CONDITION (ECM, INJECTOR ASSEMBLY CONNECTOR)
a.

Check the connector connection for the ECM and injector assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)

NG

13.CONNECT SECURELY
5.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)
a.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405886C09
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
No. 1 Injector Assembly
Tester Connection Condition Specified Condition
E-15 - E-14 Always Below 2 Ω
E-15 - E-34 Always Below 2 Ω

No. 2 Injector Assembly
Tester Connection Condition Specified Condition
E-20 - E-18 Always Below 2 Ω
E-20 - E-38 Always Below 2 Ω

No. 3 Injector Assembly
Tester Connection Condition Specified Condition
E-19 - E-18 Always Below 2 Ω
E-19 - E-38 Always Below 2 Ω

No. 4 Injector Assembly
Tester Connection Condition Specified Condition
E-16 - E-14 Always Below 2 Ω
E-16 - E-34 Always Below 2 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK DTC OUTPUT

NG

8.CHECK HARNESS AND CONNECTOR (INJECTOR HARNESS 8P CONNECTOR - ECM)
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0201, P0202, P0203 or P0204 is output A
DTCs are not output B




A

7.REPLACE ECM

B

END

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
8.CHECK HARNESS AND CONNECTOR (INJECTOR HARNESS 8P CONNECTOR - ECM)
a.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A407233C08
0.396,0.875 0.802,1.167 0.406,0.292 0.104,0.135 0.417,0.333 0.313,0.198 10 false *a 0.479,0.938 0.792,1.135 0.313,0.198 10 false Bi1
*a Front view of wire harness connector
(Injector Harness 8P Connector)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
No. 1 Injector Assembly
Tester Connection Condition Specified Condition
Bi1-1 - Bi1-2 Always Below 2 Ω

No. 2 Injector Assembly
Tester Connection Condition Specified Condition
Bi1-3 - Bi1-4 Always Below 2 Ω

No. 3 Injector Assembly
Tester Connection Condition Specified Condition
Bi1-5 - Bi1-6 Always Below 2 Ω

No. 4 Injector Assembly
Tester Connection Condition Specified Condition
Bi1-7 - Bi1-8 Always Below 2 Ω



Result:
Proceed to
OK
NG



NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR (INJECTOR HARNESS 8P CONNECTOR - ECM)

OK

10.INSPECT INJECTOR ASSEMBLY
9.REPAIR OR REPLACE HARNESS OR CONNECTOR (INJECTOR HARNESS 8P CONNECTOR - ECM)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
10.INSPECT INJECTOR ASSEMBLY
a.

Disconnect the injector assembly connector.


b.
A417903C01
0.448,0.25 0.76,0.406 0.313,0.156 10 false *1 2.542,0.219 2.854,0.375 0.313,0.156 10 false *2
*1 Injector Assembly
*2 Megohmmeter


Measure the resistance between the target's injector terminal and the injector body.


Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground Always 10 MΩ or higher
2 - Body ground Always 10 MΩ or higher


c.

Inspect the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

11.REPAIR OR REPLACE HARNESS OR CONNECTOR (INJECTOR HARNESS 8P CONNECTOR - INJECTOR ASSEMBLY)

NG

12.REPLACE INJECTOR ASSEMBLY
11.REPAIR OR REPLACE HARNESS OR CONNECTOR (INJECTOR HARNESS 8P CONNECTOR - INJECTOR ASSEMBLY)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
12.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
13.CONNECT SECURELY
a.

Connect securely the ECM connector and injector assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
14.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END