Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0217  Engine Coolant Over Temperature Condition  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0217 Engine Coolant Over Temperature Condition Diagnosis Condition:

The engine must not be stopped.


Malfunction Status:

The coolant temperature value of the coolant temperature sender is above 120°C (248°F) for 30 seconds.


Malfunction Duration:

30 seconds or more


·

Cooling fan

·

Engine coolant temperature sensor

·

ECM

·

Harness or connector


- DTC stored

MONITOR DESCRIPTION

Measure the engine coolant temperature with the engine coolant temperature sensor.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0217 After warming up engine, idle engine for 30 seconds or more.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT ENGINE ASSEMBLY
a.

Inspect the engine assembly.


Result:
Proceed to
OK
NG



OK

2.CHECK COOLING FAN

NG

15.REPAIR OR REPLACE TROUBLE AREAS
2.CHECK COOLING FAN
a.

Check the installation and damage condition of the cooling fan.


Result:
Proceed to
OK
NG



OK

3.CHECK FLUID COUPLING ASSEMBLY

NG

13.REPAIR OR REPLACE COOLING FAN
3.CHECK FLUID COUPLING ASSEMBLY
a.

Check the installation of the fluid coupling assembly.


Result:
Proceed to
OK
NG



OK

4.CHECK CONNECTOR CONNECTION CONDITION (ENGINE COOLANT TEMPERATURE SENSOR)

NG

12.REPAIR OR REPLACE FLUID COUPLING ASSEMBLY
4.CHECK CONNECTOR CONNECTION CONDITION (ENGINE COOLANT TEMPERATURE SENSOR)
a.

Check the connector connection for the engine coolant temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

5.CHECK ENGINE COOLANT TEMPERATURE SENSOR

NG

11.CONNECT SECURELY
5.CHECK ENGINE COOLANT TEMPERATURE SENSOR
a.

Check the installation of the engine coolant temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of engine coolant temperature sensor.


Result:
Proceed to
OK
NG



OK

6.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

10.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
6.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

7.CHECK DTC OUTPUT

NG

9.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0217 is output A
DTCs are not output B




A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
9.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
10.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Repair or replace the engine coolant temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the engine coolant temperature sensor.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
11.CONNECT SECURELY
a.

Connect securely the engine coolant temperature sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
12.REPAIR OR REPLACE FLUID COUPLING ASSEMBLY
a.

Properly install the fluid coupling assembly.

HINT:

Replace the fluid coupling assembly if it is leak.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
13.REPAIR OR REPLACE COOLING FAN
a.

Properly install the cooling fan.

HINT:

Replace the cooling fan if it is damaged.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
14.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

15.REPAIR OR REPLACE TROUBLE AREAS
a.

Repair or replace the trouble areas.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT