Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0422  Catalyst 2 Efficiency Below Threshold Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0422 Catalyst 2 Efficiency Below Threshold Bank 1 Diagnosis Condition:
·

Determined during completion of DPR regeneration with the engine running.

·

The exhaust gas flow rate is 150 to 350 kg/h.

·

The engine revolution is 1050 to 2250 rpm.

·

The fuel injection quantity is 20 to 150 mm3/st.

·

A change in the engine revolution is 625 rpm or less.

·

A change in the fuel injection quantity is 625 mm3/sec or less.

·

The vehicle speed is 30 km/h (19 mile) or more.

And, the conditions described below remain for 10 seconds.

·

The predicted detection temperature of the No. 3 exhaust gas temperature sensor calculated by the ECM is 385°C (725°F) or more.


Malfunction Status:

The temperature detected at the No. 3 exhaust gas temperature sensor remains 385°C (725°F) or less for 30 seconds.


Malfunction Duration:

30 seconds or more


·

No. 3 Exhaust gas temperature sensor

·

Monolithic converter assembly

·

Low quality fuel


Class B1 DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0422 PM forced regeneration


CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FUEL
a.

Open the fuel cap and check fuel for abnormality (in color and smell).


Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 EXHAUST GAS TEMPERATURE SENSOR)

NG

9.REPLACE FUEL
2.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 EXHAUST GAS TEMPERATURE SENSOR)
a.

Check the connector connection for the No. 3 exhaust gas temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR

NG

8.CONNECT SECURELY
3.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 3 exhaust gas temperature sensor.


b.

Check the sensing area of the No. 3 exhaust gas temperature sensor for dirt, clogging, and damage.


Result:
Proceed to
OK
NG



OK

4.REPLACE MONOLITHIC CONVERTER ASSEMBLY

NG

7.REPAIR OR REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
4.REPLACE MONOLITHIC CONVERTER ASSEMBLY
a.

Replace the monolithic converter assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>MONOLITHIC CONVERTER>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.PERFORM PM FORCED REGENERATION
5.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.



Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPAIR OR REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the No. 3 exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 3 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

5.PERFORM PM FORCED REGENERATION
8.CONNECT SECURELY
a.

Connect securely the No. 3 exhaust gas temperature sensor.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

5.PERFORM PM FORCED REGENERATION
9.REPLACE FUEL
a.

Replace the fuel with good quality fuel.


Result:
Proceed to
NEXT



NEXT

10.PERFORM PM FORCED REGENERATION
10.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT
11.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Result:
Result Proceed to
DTC P0422 is output A
DTCs are not output B




A

2.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 EXHAUST GAS TEMPERATURE SENSOR)

B

END