Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0704  Clutch Switch Input Circuit  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0704 Clutch Switch Input Circuit Diagnosis Condition:
·

Vehicle speed is 80 km/h (50 mile) or more for 10 seconds. After that, vehicle speed is 0 km/h (0 mile).

·

MT model


Malfunction Status:

Presence/absence of input of exhaust brake main switch signals cannot be sensed after 5 or more cycles of "vehicle stop (vehicle speed = 0 km/h (0 mile)) → run → stop".


Malfunction Duration:

-


·

Exhaust brake main switch

·

Harness or connector

·

ECM


Class C DTC stored

MONITOR DESCRIPTION

Presence/absence of input of exhaust brake main switch signals is sensed by the ECM through the exhaust brake main switch.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0704 Repeat the following procedure 5 times or more:
stop the vehicle (vehicle speed = 0 km/h), drive it, and then stop it again

WIRING DIAGRAM

A407168E05
0.885,1.75 1.198,1.948 0.313,0.198 10 false H3 0.875,1.938 3.271,2.438 2.396,0.5 10 false Exhaust Brake Main Switch 2.281,0.979 2.594,1.177 0.313,0.198 10 false 2 4.333,1.104 4.646,1.302 0.313,0.198 10 false V-55 4.792,1.104 5.219,1.313 0.427,0.208 10 false A115 4.854,0.906 5.167,1.104 0.313,0.198 10 false 17 5.26,1.125 5.958,1.646 0.698,0.521 10 false CLSW 5.667,1.99 6.365,2.51 0.698,0.521 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK EXHAUST BRAKE MAIN SWITCH
a.

Check the exhaust brake main switch if it is properly adjusted.


Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR CONNECTION CONDITION

NG

10.ADJUST WINDSHIELD WIPER SWITCH ASSEMBLY
2.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the exhaust brake main switch connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.INSPECT EXHAUST BRAKE MAIN SWITCH

NG

9.CONNECT SECURELY
3.INSPECT EXHAUST BRAKE MAIN SWITCH
a.

Inspect the exhaust brake main switch.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SHORT IN WIRE HARNESS)

NG

8.REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (SHORT IN WIRE HARNESS)
A405887C06
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false V
*a Signal Check Harness Lead Connector


a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V-55 - Body ground Ignition switch ON
Clutch Pedal Depressed
11 V or higher
Ignition switch ON
Clutch Pedal Released
Below 1 V



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
8.REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY
a.

Replace the windshield wiper switch assembly.


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
9.CONNECT SECURELY
a.

Connect securely the windshield wiper switch assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
10.ADJUST WINDSHIELD WIPER SWITCH ASSEMBLY
a.

Adjust the windshield wiper switch assembly.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT