Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P1426  Differential Pressure Sensor Range/Performance  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1426 Differential Pressure Sensor Range/Performance Diagnosis Condition:

Elapse of at least 2 seconds after engine stop


Malfunction Status:

Differential pressure remains less than -2 kPa or higher than 2 kPa for 2 seconds.


Malfunction Duration:

2 seconds or more


·

Differential pressure sensor

·

Harness or connector

·

ECM


Class B1 DTC stored

MONITOR DESCRIPTION

It detects a difference between pressure at the inlet of the muffler and at the outlet of the monolithic converter assembly and monitors any failure or malfunction of the DPR.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P1426 Stop the engine and wait for at least 2 seconds or more.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HOSE AND PIPE
a.

Check if the hose and pipe are cracked, bent, ruptured, or clogged.


Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR CONNECTION CONDITION (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY CONNECTOR)

NG

15.CLEAN AND REPLACE HOSE AND PIPE
2.CHECK CONNECTOR CONNECTION CONDITION (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY CONNECTOR)
a.

Check the connector connection for the differential pressure sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

NG

14.CONNECT SECURELY
3.CHECK DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
a.

Check the installation of the differential pressure sensor assembly.


b.

Make sure there is no dirt, damage or clogging in the differential pressure sensor assembly.


Result:
Proceed to
OK
NG



OK

4.INSPECT DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

NG

13.REPAIR OR REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
4.INSPECT DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
a.

Disconnect the differential pressure sensor assembly connector.


A407856C05
0.135,0.177 0.448,0.375 0.313,0.198 10 false *a
*a Component without harness connected
(Differential Pressure Sensor Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 2 to 15 kΩ
2 - 3 Always 2 to 15 kΩ



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS OR CONNECTOR (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - ECM)

NG

12.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
5.CHECK HARNESS OR CONNECTOR (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the differential pressure sensor assembly connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-71- Body ground and other terminals Always 10 kΩ or higher
V-70 - Body ground and other terminals Always 10 kΩ or higher
V-46 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS OR CONNECTOR (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - ECM)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK HARNESS OR CONNECTOR (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - ECM)
a.

Turn the ignition switch off.


b.

Connect the differential pressure sensor assembly connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-71 - V-70 Always 2 to 15 kΩ
V-46 - V-70 Always 2 to 15 kΩ



Result:
Proceed to
OK
NG



OK

7.CHECK DTC OUTPUT

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P1426 is output A
DTCs are not output B




A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
9.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
12.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
a.

Replace the differential pressure sensor assembly.


Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
13.REPAIR OR REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
a.

Repair or replace the differential pressure sensor assembly.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the differential pressure sensor assembly.



Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
14.CONNECT SECURELY
a.

Connect securely the differential pressure sensor assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
15.CLEAN AND REPLACE HOSE AND PIPE
a.

Clean or replace the hose and pipe.


Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT