Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P1515  Charge Air Cooler Efficiency Low  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1515 Charge Air Cooler Efficiency Low Diagnosis Condition:
·

The conditions described below remain for 11 seconds or more.

-

The battery voltage is in the range of 10 to 16 V.

-

The condition that the engine speed remains at 500 rpm or more for 5 seconds or more.



·

The conditions described below remain for 40 seconds or more.

-

The engine speed is 1200 rpm or more.

-

Fuel injection quantity is 25 mm3/st or more.

-

A change in the engine speed is 664 rpm or less.

-

A change in fuel injection quantity is 78 mm3/st or less.

-

Atmospheric pressure is higher than 75 kPa.

-

Vehicle speed is 21 km/h (13 mile) or more.

-

Intake air flow rate is 30 g/s or more.

-

Intake air temperature is -10°C (14°F) or more.

-

Exhaust brake and DPR are not actuated.



Malfunction Status:
·

The following conditions are detected.

-

The detected intake manifold intake air temperature minus the actual intake manifold intake air temperature is less than 40°C (104°F) if the EGR activation rate is 0%; less than 47°C (116.6°F) if the EGR activation rate is less than 20%; or less than 90°C (194°F) if the EGR activation rate is 60%.

-

The intercooler efficiency, which is calculated based on the intake air temperature sensor, manifold absolute pressure sensor, and intake air temperature sensor (for intercooler side) and atmospheric pressure sensor, is less than 40%.



Malfunction Duration:

-


·

Intercooler assembly

·

Radiator assembly

·

Radiator fan

·

Fluid coupling assembly

·

Air cleaner filter element sub-assembly


Class B1 DTC stored

MONITOR DESCRIPTION

The intercooler cooling efficiency is monitored by comparing the intake temperature and intercooler out temperature measured by the mass air flow meter.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P1515 Idle the engine for 40 seconds or more.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P1515 is output A
DTC P1515 and other DTC are output B


HINT:

When P0096, P0101, P0106, or P2227 is output, it may have been detected due to a malfunction in the inlet air temperature switch, mass air flow meter sub-assembly, air pressure sensor assembly, or atmospheric pressure sensor.




A

2.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

B

2.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Check there is no dirt, damage or clogging in the air cleaner filter element sub-assembly.


Result:
Proceed to
OK
NG



OK

3.CHECK RADIATOR FAN

NG

14.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
3.CHECK RADIATOR FAN
a.

Check that the radiator fan (fan blades) was damaged.


Result:
Proceed to
OK
NG



OK

4.CHECK FLUID COUPLING ASSEMBLY

NG

13.REPLACE RADIATOR FAN
4.CHECK FLUID COUPLING ASSEMBLY
a.

Check if silicone oil is leaking from the fluid coupling assembly.


Result:
Proceed to
OK
NG



OK

5.CHECK INTERCOOLER ASSEMBLY

NG

12.REPLACE FLUID COUPLING ASSEMBLY
5.CHECK INTERCOOLER ASSEMBLY
a.

Check that the intercooler outer fin was clogged or damaged.


Result:
Proceed to
OK
NG



OK

6.CHECK INTERCOOLER TUBES

NG

11.REPLACE INTERCOOLER ASSEMBLY
6.CHECK INTERCOOLER TUBES
a.

Check if the intercooler tubes are abnormally swollen or cracked.


Result:
Proceed to
OK
NG



OK

7.CHECK RADIATOR ASSEMBLY

NG

10.REPLACE INTERCOOLER ASSEMBLY
7.CHECK RADIATOR ASSEMBLY
a.

Check if the radiator outer fins are clogged or damaged.


Result:
Proceed to
OK
NG



OK

8.CHECK DTC OUTPUT

NG

9.REPLACE RADIATOR ASSEMBLY
8.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

9.REPLACE RADIATOR ASSEMBLY
a.

Replace the radiator assembly.

Click hereEngine / Hybrid System>N04C-WA (COOLING)>RADIATOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
10.REPLACE INTERCOOLER ASSEMBLY
a.

Replace the intercooler assembly.


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
11.REPLACE INTERCOOLER ASSEMBLY
a.

Replace the intercooler assembly.


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
12.REPLACE FLUID COUPLING ASSEMBLY
a.

Replace the fluid coupling assembly.

Click hereEngine / Hybrid System>N04C-WA (COOLING)>FAN>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
13.REPLACE RADIATOR FAN
a.

Replace the radiator fan.

Click hereEngine / Hybrid System>N04C-WA (COOLING)>FAN>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
14.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Replace or clean the air cleaner filter element sub-assembly.


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT