Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P20CD  Exhaust Aftertreatment Fuel Injector "A" Control Circuit Low  P20CE  Exhaust Aftertreatment Fuel Injector "A" Control Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P20CD Exhaust Aftertreatment Fuel Injector "A" Control Circuit Low Diagnosis Condition:
·

Ignition switch ON

·

The battery voltage is in the range of 10 to 16 V.


Malfunction Status:

The condition that the exhaust fuel addition injector circuit voltage is 2.8 V or less remains for 12 seconds or more.


Malfunction Duration:

12 seconds or more


·

Fuel addition cut valve assembly

·

Exhaust fuel addition injector assembly signal line

·

ECM


Class C DTC stored
P20CE Exhaust Aftertreatment Fuel Injector "A" Control Circuit High Diagnosis Condition:
·

Ignition switch ON

·

The battery voltage is in the range of 10 to 16 V.


Malfunction Status:

When command of fuel injection is continued to 745 times and the exhaust fuel addition injector circuit voltage is 3.0 V or higher.


Malfunction Duration:

-


·

Fuel addition cut valve assembly

·

Exhaust fuel addition injector assembly signal line

·

ECM


Class C DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20CD Ignition switch ON for 12 seconds or more.
P20CE Drive the vehicle for 20 minutes or more and check that the value of the exhaust temperature sensor is 250°C or higher.

WIRING DIAGRAM

A451043E01
5.802,0.365 6.26,0.563 0.458,0.198 10 false FIV 5.781,1.604 6.24,1.802 0.458,0.198 10 false MREL 5.792,2.146 6.25,2.344 0.458,0.198 10 false MREL 5.802,2.708 6.26,2.906 0.458,0.198 10 false E01 3.146,0.781 5.76,1.146 2.615,0.365 10 false Exhaust Fuel Addition Injector Assembly 3.167,0.615 3.625,0.813 0.458,0.198 9 false j6 2.573,0.51 3.198,0.708 0.625,0.198 10 false EFI NO.2 1.573,1.896 2.292,2.125 0.719,0.229 10 false ACT PWR 2.219,1.063 2.677,1.26 0.458,0.198 10 false 5 2.219,1.469 2.677,1.667 0.458,0.198 10 false 2 1.458,1.469 1.917,1.667 0.458,0.198 10 false 1 1.448,1.063 1.906,1.26 0.458,0.198 10 false 3 0.385,2.042 1.104,2.271 0.719,0.229 10 false EFI-MAIN 0.375,2.604 1.094,2.833 0.719,0.229 10 false P/I 0.708,1.74 1.427,1.969 0.719,0.229 10 false EFI NO.1 0.365,3.188 1.323,3.448 0.958,0.26 10 false R/B NO.2-B 0.49,4.281 1.208,4.51 0.719,0.229 10 false Battery 0.396,3.76 1.354,4.021 0.958,0.26 10 false FL-MAIN 5.365,0.344 5.823,0.542 0.458,0.198 10 false B142 5.375,1.573 5.833,1.771 0.458,0.198 10 false A115 5.375,2.125 5.833,2.323 0.458,0.198 10 false A115 5.375,2.677 5.833,2.875 0.458,0.198 10 false A115 5.448,0.177 5.906,0.375 0.458,0.198 10 false 27 5.458,1.938 5.917,2.135 0.458,0.198 10 false 27 5.479,1.385 5.938,1.583 0.458,0.198 10 false 26 5.448,2.479 5.906,2.677 0.458,0.198 10 false 12 5,2.667 5.458,2.865 0.458,0.198 10 false V-40 5,1.573 5.458,1.771 0.458,0.198 10 false V-23 5.021,2.115 5.479,2.313 0.458,0.198 10 false V-3 5.031,0.333 5.49,0.531 0.458,0.198 10 false E-5 6.188,3.177 6.729,3.406 0.542,0.229 10 false ECM 4.219,0.208 4.677,0.406 0.458,0.198 10 false 2 3.469,0.198 3.927,0.396 0.458,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the exhaust fuel addition injector assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

NG

13.CONNECT SECURELY
2.CHECK EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Check the installation of the exhaust fuel addition injector assembly.


Result:
Proceed to
OK
NG



OK

3.CHECK EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

NG

12.REPAIR OR REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
3.CHECK EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
A165237C05
0.344,0.906 0.833,1.198 0.49,0.292 0.094,0.104 0.5,0.427 0.406,0.323 10 false *a 0.552,0.99 0.875,1.188 0.323,0.198 10 false j6
*a Front view of wire harness connector
(to Exhaust Fuel Addition Injector Assembly)


a.

Disconnect the exhaust fuel addition injector assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
j6-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
A165237C05
0.344,0.906 0.833,1.198 0.49,0.292 0.094,0.104 0.5,0.427 0.406,0.323 10 false *a 0.552,0.99 0.875,1.188 0.323,0.198 10 false j6
*a Front view of wire harness connector
(to Exhaust Fuel Addition Injector Assembly)


a.

Disconnect the ECM connector.


b.

Disconnect the exhaust fuel addition injector assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
j6-2 - Body ground and other terminals Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.PERFORM PM FORCED REGENERATION

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Result:
Result Proceed to
DTC P20CD and P20CE are output A
DTCs are not output B




A

7.REPLACE ECM

B

END

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.PERFORM PM FORCED REGENERATION
8.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
9.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.PERFORM PM FORCED REGENERATION
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.PERFORM PM FORCED REGENERATION
12.REPAIR OR REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Install the exhaust fuel addition injector assembly correctly.

If damage is found, replace the exhaust fuel addition injector assembly.

HINT:

If damage is found, replace the exhaust fuel addition injector assembly.



Result:
Proceed to
NEXT



NEXT

8.PERFORM PM FORCED REGENERATION
13.CONNECT SECURELY
a.

Connect securely the exhaust fuel addition injector assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

8.PERFORM PM FORCED REGENERATION