Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P20DF  Exhaust Aftertreatment Fuel Pressure Sensor Circuit Low  P20E0  Exhaust Aftertreatment Fuel Pressure Sensor Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P20DF Exhaust Aftertreatment Fuel Pressure Sensor Circuit Low Diagnosis Condition:
·

Ignition switch ON

·

The battery voltage is in the range of 10 to 16 V.

·

The starter is stopped.


Malfunction Status:

Output of the No. 2 fuel pressure sensor remains at 0.19 V (-0.13 MPa) or less for at least 3 seconds.


Malfunction Duration:

3 seconds or more


·

No. 2 fuel pressure sensor

·

Harness or connector

·

ECM


Class B1 DTC stored
P20E0 Exhaust Aftertreatment Fuel Pressure Sensor Circuit High Diagnosis Condition:
·

Ignition switch ON

·

The battery voltage is in the range of 10 to 16 V.

·

The starter is stopped.


Malfunction Status:

Output of the No. 2 fuel pressure sensor remains at 4.73 V (2.13 MPa) or more for at least 3 seconds.


Malfunction Duration:

3 seconds or more


·

No. 2 fuel pressure sensor

·

Harness or connector

·

ECM


Class B1 DTC stored

MONITOR DESCRIPTION

The ECM detected abnormality in the No. 2 fuel pressure sensor.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20DF
P20E0
Ignition switch ON for 3 seconds or more

WIRING DIAGRAM

A451045E01
5.604,2.375 6.156,2.604 0.552,0.229 10 false ECM 5.208,0.688 5.667,0.885 0.458,0.198 10 false FPR 5.198,1.188 5.656,1.385 0.458,0.198 10 false VC 5.208,1.667 5.667,1.865 0.458,0.198 10 false E4 4.792,1.635 5.25,1.833 0.458,0.198 10 false B142 4.792,1.146 5.25,1.344 0.458,0.198 10 false B142 4.802,0.656 5.26,0.854 0.458,0.198 10 false B142 4.427,0.656 4.885,0.854 0.458,0.198 10 false V-48 4.427,1.146 4.885,1.344 0.458,0.198 10 false M-51 4.438,1.635 4.896,1.833 0.458,0.198 10 false E-77 4.906,0.5 5.365,0.698 0.458,0.198 10 false 1 4.854,0.99 5.313,1.188 0.458,0.198 10 false 68 4.875,1.479 5.333,1.677 0.458,0.198 10 false 90 1.646,1.188 2.104,1.385 0.458,0.198 10 false VC 1.656,1.677 2.115,1.875 0.458,0.198 10 false E2 1.656,0.698 2.115,0.896 0.458,0.198 10 false PR 0.615,2.406 2.604,2.625 1.99,0.219 10 false No. 2 Fuel Pressure Sensor 0.625,2.229 1.083,2.427 0.458,0.198 10 false B146 1.948,0.563 2.406,0.76 0.458,0.198 10 false 2 1.958,1.031 2.417,1.229 0.458,0.198 10 false 3 1.948,1.521 2.406,1.719 0.458,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FUEL PRESSURE SENSOR)
a.

Check the connector connection for the No. 2 fuel pressure sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK NO. 2 FUEL PRESSURE SENSOR

NG

12.CONNECT SECURELY
2.CHECK NO. 2 FUEL PRESSURE SENSOR
a.

Check the installation of the No. 2 fuel pressure sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of No. 2 fuel pressure sensor.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

NG

11.REPAIR OR REPLACE NO. 2 FUEL PRESSURE SENSOR
3.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Disconnect the No. 2 fuel pressure sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C17
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-48 - Body ground and other terminals Always 10 kΩ or higher
M-51 - Body ground and other terminals Always 10 kΩ or higher
E-77 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS OR CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS OR CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Disconnect the No. 2 fuel pressure sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A204467C81
0.49,1.031 1.052,1.354 0.563,0.323 1.156,1.833 1.469,1.271 true 2.302,1.813 1.948,1.271 true 1.708,1.844 1.667,1.281 true 0.094,0.146 0.406,0.344 0.313,0.198 10 false *a 0.615,1.115 1.115,1.313 0.5,0.198 10 false B146 1.646,1.896 1.958,2.094 0.313,0.198 10 false PR 2.271,1.896 2.583,2.094 0.313,0.198 10 false VC 1.063,1.885 1.375,2.083 0.313,0.198 10 false E2
*a Front view of wire harness connector
(to No. 2 Fuel Pressure Sensor)


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C17
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-48 - B146-2 (PR) Always Below 1 Ω
M-51 - B146-3 (VC) Always Below 1 Ω
E-77 - B146-1 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK NO. 2 FUEL PRESSURE SENSOR

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK NO. 2 FUEL PRESSURE SENSOR
a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C17
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M-51 - E-77 Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

6.CHECK DTC OUTPUT

NG

8.INSPECT WIRE HARNESS AND ECM
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P20DF and P20E0 are output A
DTCs are not output B




A

7.REPLACE ECM

B

END

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT
8.INSPECT WIRE HARNESS AND ECM
a.

Inspect the wire harness and ECM sensor power supply output value.


Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT
11.REPAIR OR REPLACE NO. 2 FUEL PRESSURE SENSOR
a.

Clean the sensing area and install the sensor properly.

HINT:

If damaged, replace the No. 2 fuel pressure sensor.



Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT
12.CONNECT SECURELY
a.

Connect securely No. 2 fuel pressure sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT
13.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END