Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P2226  Barometric Pressure Sensor "A" Circuit  P2228  Barometric Pressure Sensor "A" Circuit Low  P2229  Barometric Pressure Sensor "A" Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2226 Barometric Pressure Sensor "A" Circuit Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V


Malfunction Status:

Malfunction of communication with the atmospheric pressure sensor remains for at least 1 second.


Malfunction Duration:

1 second or more


ECM - DTC stored
P2228 Barometric Pressure Sensor "A" Circuit Low Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine runs at idle for at least 30 seconds.


Malfunction Status:

Atmospheric pressure sensor pressure remains at 40 kPa or less for 1 second or more.


Malfunction Duration:

1 second or more


ECM Class B1 DTC stored
P2229 Barometric Pressure Sensor "A" Circuit High Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine runs at idle for at least 30 seconds.


Malfunction Status:

Atmospheric pressure sensor pressure remains at 115 kPa or more for 30 seconds or more.


Malfunction Duration:

30 seconds or more


ECM Class B1 DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2226 Ignition switch ON for 1 second or more.
P2228
P2229
Ignition switch ON for 3 seconds or more or idle the engine for 30 seconds or more.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P2226, P2228 or P2229 is output A
DTC P2226, P2228 or P2229 and other DTCs are output B




A

2.CHECK DTC OUTPUT

B

2.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P2226, P2228 or P2229 is output A
DTCs are not output B




A

3.REPLACE ECM

B

END

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END