Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P2227  Barometric Pressure Sensor "A" Circuit Range/Performance  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2227 Barometric Pressure Sensor "A" Circuit Range/Performance Diagnosis Condition:
·

The engine speed is in the range of 570 to 1200 rpm.

·

The fuel injection quantity is in the range of 0 mm3/st to 35 mm3/st.

·

Engine coolant temperature is 55°C (131°F) or less.

·

EGR valve opening is 0% or less (EGR-CUT state).

·

Exhaust brake is not actuated.


Malfunction Status:
·

Compare a theoretical air volume calculated from a boost pressure and an atmospheric pressure with an actual air volume for 10 seconds or more. The rate of the theoretical air volume to the actual air volume is higher than 0.75 or less than 1.15.

·

As well as, difference between the current DCY value of the aforementioned value and the current DCY value is less than 0.10.

·

In addition, the condition that the difference between the average boost pressure and the average atmospheric pressure is 18 kPa or more after the engine stops by switching off the key of the previous DCY remains for 3 seconds or more.


Malfunction Duration:

3 seconds or more.


ECM Class B1 DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2227 Ignition switch ON for 10 seconds or more.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (MANIFOLD ABSOLUTE PRESSURE SENSOR CONNECTOR)
a.

Check the connector connection for the manifold absolute pressure sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

6.CONNECT SECURELY
2.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Check the installation of the manifold absolute pressure sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of manifold absolute pressure sensor.


Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

5.REPAIR OR REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P2227 is output A
DTCs are not output B




A

4.REPLACE ECM

B

END

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
5.REPAIR OR REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Repair or replace the manifold absolute pressure sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the manifold absolute pressure sensor.



Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
6.CONNECT SECURELY
a.

Connect securely the manifold absolute pressure sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END