Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P2458  Particulate Filter Regeneration Duration Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2458 Particulate Filter Regeneration Duration Bank 1 Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V

·

The engine speed remains at 500 rpm or more.

·

DPR manual regenerating.

·

Do not detect the No. 3 exhaust gas temperature sensor of failure.


Malfunction Status:

After a manual DPR regeneration is started, the DOC temperature is still below 200°C (392°F) and the ATC temperature is still below 230°C (446°F) even after 30 minutes.


Malfunction Duration:

-


·

Fuel pressure sensor (built into common rail assembly)

·

Harness or connector

·

ECM


- DTC stored

MONITOR DESCRIPTION

·

The DPR performs PM regeneration by increasing DOC temperature using the engine warm up control.

·

During a manual regeneration, warm up control is carried out by idle up, exhaust brake closing, VNT control, after injection, post injection and dosing valve injection.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2458 PM forced regeneration

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

After using this DTC to check and repair, check the engine oil amount.

·

Replace the engine oil if it exceeds the upper level of the level gauge (X mark: 25 mm over the upper level of a standard level gauge).



PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P2458 is output A
DTC P2458 and other DTCs are output B




A

2.CHECK EXHAUST PIPE

B

2.CHECK EXHAUST PIPE
a.

Check for exhaust pipe crack (between the turbocharger and DPR), exhaust gas leak (soot contamination) and improper coupling flange tightening.


Result:
Proceed to
OK
NG



OK

3.CHECK EXHAUST RETARDER ASSEMBLY

NG

28.REPAIR EXHAUST PIPE
3.CHECK EXHAUST RETARDER ASSEMBLY
a.

Check the exhaust retarder assembly for unease and sticking.


Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (INJECTION VOLUME, ENGINE SPEED)

NG

27.REPAIR OR REPLACE EXHAUST RETARDER ASSEMBLY
4.READ VALUE USING GTS (INJECTION VOLUME, ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Injection Volume


e.

Read the value displayed on the GTS.


Standard:
Item Condition Reference Value
Engine Speed
·

Engine speed: 1500 rpm

·

Engine coolant temperature: 80°C or higher

·

Shift position N

·

A/C OFF

·

Air compressor OFF


Speed fluctuation amount is 15 rpm or less
Injection Volume 5 mm3/st or more


Result:
Proceed to
OK
NG



OK

5.CHECK READ VALUE USING GTS (INJECTION VOLUME, ENGINE SPEED)

NG

26.REPLACE INJECTOR ASSEMBLY
5.CHECK READ VALUE USING GTS (INJECTION VOLUME, ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Injection Volume


e.

Read the value displayed on the GTS.


f.

Check that the injection volume changes when the exhaust brake is being operating/not operated.


Standard:
Item Condition Reference Value
Injection Volume
·

Engine Speed: 980 rpm

·

Coolant Temperature: 80°C or more

·

With no load on engine (air conditioning off, air compressor off, and any other devices placing a load on the engine turned off)


8 to 12 mm3/st


Result:
Proceed to
OK
NG



OK

6.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR

NG

25.ADJUST EXHAUST RETARDER ASSEMBLY
6.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 3 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the No. 3 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

7.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR

NG

24.REPAIR OR REPLACE EXHAUST GAS TEMPERATURE SENSOR NO.3
7.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 3 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
OK
NG



OK

8.CHECK NO. 1 EXHAUST GAS TEMPERATURE SENSOR

NG

23.REPAIR OR REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
8.CHECK NO. 1 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 1 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the No. 1 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

9.INSPECT NO. 1 EXHAUST GAS TEMPERATURE SENSOR

NG

22.REPAIR OR REPLACE NO. 1 EXHAUST GAS TEMPERATURE SENSOR
9.INSPECT NO. 1 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 1 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

10.INSPECT MONOLITHIC CONVERTER ASSEMBLY

NG

21.REPLACE NO. 1 EXHAUST GAS TEMPERATURE SENSOR
10.INSPECT MONOLITHIC CONVERTER ASSEMBLY
a.

Remove monolithic converter assembly and check that there is no soot leaking at the rear edge of the monolithic converter assembly, no damage, and no other abnormality.


Result:
Proceed to
OK
NG



OK

11.CHECK ENGINE COOLANT TEMPERATURE SENSOR

NG

20.REPLACE MONOLITHIC CONVERTER ASSEMBLY
11.CHECK ENGINE COOLANT TEMPERATURE SENSOR
a.

Check the installation of the engine coolant temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the engine coolant temperature sensor.


Result:
Proceed to
OK
NG



OK

12.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

19.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
12.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

13.PERFORM ACTIVE TEST USING GTS (OPERATE TURBOCHARGER SUB-ASSEMBLY)

NG

18.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
13.PERFORM ACTIVE TEST USING GTS (OPERATE TURBOCHARGER SUB-ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the VN Turbo Position / Data List / Target VN Turbo Position / Actual VN Turbo Position.


d.

Check each step from 90 to 0% of the time lag of the target VN turbo position and actual VN turbo position.

NOTICE:

Perform the inspection while the engine is stopped to avoid engine damages.


Standard:

The response delay should be less than 3 seconds.



Result:
Proceed to
OK
NG



OK

14.PERFORM PM FORCED REGENERATION

NG

17.REPLACE TURBOCHARGER SUB-ASSEMBLY
14.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Result Proceed to
Manual forced regeneration completed normally A
Manual forced regeneration does not complete normally B



A

15.CHECK DTC OUTPUT

B

16.CHECK DTC OUTPUT
15.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

16.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Perform the inspection procedure for the output DTCs.


Result:
Proceed to
NEXT



NEXT

17.REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Replace the turbocharger sub-assembly.

Click hereEngine / Hybrid System>N04C-WA (INTAKE)>TURBOCHARGER>REMOVAL


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
18.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
19.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Repair or replace the engine coolant temperature sensor.

HINT:

If damaged, replace the engine coolant temperature sensor.

Clean the sensing unit and install it properly.



Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
20.REPLACE MONOLITHIC CONVERTER ASSEMBLY
a.

Replace the monolithic converter assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>MONOLITHIC CONVERTER>REMOVAL


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
21.REPLACE NO. 1 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 1 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
22.REPAIR OR REPLACE NO. 1 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 1 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
23.REPAIR OR REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 3 exhaust gas temperature sensor

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
24.REPAIR OR REPLACE EXHAUST GAS TEMPERATURE SENSOR NO.3
a.

Repair or replace the No. 3 exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 3 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
25.ADJUST EXHAUST RETARDER ASSEMBLY
a.

Adjust the butterfly opening of the exhaust retarder assembly.

Click hereBrake>EXHAUST BRAKE>EXHAUST BRAKE RETARDER>INSPECTION


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
26.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
27.REPAIR OR REPLACE EXHAUST RETARDER ASSEMBLY
a.

Check the exhaust brake valve for unease and sticking

HINT:

Replace if needed.



Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
28.REPAIR EXHAUST PIPE
a.

Repair of exhaust pipe (replace gasket, retighten).

HINT:

Replace if needed.



Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
29.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END