Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P24A2  Particulate Filter Regeneration Incomplete Bank 1  


DESCRIPTION

The engine ECU monitors accumulate post fuel injection quantity at DPR regeneration.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P24A2 Particulate Filter Regeneration Incomplete Bank 1 Diagnosis Condition:

While the engine is in operation


Malfunction Status:

Accumulate post fuel injection quantity exceeds 2000 cc.


Malfunction Duration:

-


·

Exhaust gas leakage

·

Monolithic converter assembly damage

·

Exhaust fuel addition injector quantity

·

Improper adjustment of exhaust brake valve

·

Failure of No. 3 exhaust gas temperature sensor


Class C DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P24A2 PM forced regeneration

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

After using this DTC to check and repair, check the engine oil amount.

·

Replace the engine oil if it exceeds the upper level of the level gauge (X mark: 25 mm over the upper level of a standard level gauge).



PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P24A2 is output A
DTC P24A2 and other DTCs are output B




A

2.CHECK EXHAUST PIPE

B

2.CHECK EXHAUST PIPE
a.

Check for exhaust pipe crack, exhaust gas leak (soot contamination) and improper coupling flange tightening.


Result:
Proceed to
OK
NG



OK

3.CHECK READ VALUE USING GTS (INJECTION VOLUME, ENGINE SPEED)

NG

22.REPAIR OR REPLACE EXHAUST PIPE
3.CHECK READ VALUE USING GTS (INJECTION VOLUME, ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed / Injection Volume


e.

Read the value.


Standard:
Item Condition Reference Value
Engine Speed
·

Engine speed: 1500rpm

·

Engine coolant temperature: 80°C or higher

·

Shift position N

·

A/C OFF

·

Air compressor OFF


Speed fluctuation amount is 15 rpm or less
Injection Volume 5 mm3/st or more


Result:
Proceed to
OK
NG



OK

4.CHECK READ VALUE USING GTS (INJECTION VOLUME)

NG

21.REPLACE INJECTOR ASSEMBLY
4.CHECK READ VALUE USING GTS (INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Injection Volume


e.

Read the value displayed on the GTS.


f.

Check that the injection volume changes when the exhaust brake is being operating/not operated.

Standard:
Item Condition Reference Value
Injection Volume
·

Engine Speed: 980 rpm

·

Coolant Temperature: 80°C or more

·

With no load on engine (air conditioning off, air compressor off, and any other devices placing a load on the engine turned off)


10 to 18 mm3/st


HINT:

The fuel injection volume must change when the exhaust retarder switch is turned on/off.



Result:
Proceed to
OK
NG



OK

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR VALVE POSITION)

NG

20.ADJUST EXHAUST RETARDER ASSEMBLY
5.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR VALVE POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Valve Position / Data List / Actual EGR Valve Position and Target EGR Valve Position


d.

Check each step from 90 to 0% of the time lag of the target EGR valve opening and actual EGR valve opening.

NOTICE:

Perform the inspection while the engine is stopped to avoid engine damages.


Standard:

The response delay should be less than 5 seconds.



Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS (CONTROL THE VN TURBO POSITION)

NG

19.REPLACE EGR VALVE ASSEMBLY
6.PERFORM ACTIVE TEST USING GTS (CONTROL THE VN TURBO POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the VN Turbo Position / Data List / Target VN Turbo Position / Actual VN Turbo Position


d.

Check each step from 90 to 0% of the time lag of the target VN turbo position and actual VN turbo position.

NOTICE:

Perform the inspection while the engine is stopped to avoid engine damages.


Standard:

The response delay should be less than 3 seconds.



Result:
Proceed to
OK
NG



OK

7.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR

NG

18.REPLACE TURBOCHARGER SUB-ASSEMBLY
7.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 3 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the No. 3 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR

NG

17.REPAIR OR REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
8.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 3 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
OK
NG



OK

9.CHECK FRONT EXHAUST PIPE ASSEMBLY

NG

16.REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
9.CHECK FRONT EXHAUST PIPE ASSEMBLY
a.

Check if the front exhaust pipe assembly is clogged, punctured, or bent.


Result:
Proceed to
OK
NG



OK

10.CHECK ENGINE OIL LEVEL

NG

15.REPLACE FRONT EXHAUST PIPE ASSEMBLY
10.CHECK ENGINE OIL LEVEL
a.

Check the engine oil level.


Result:
Proceed to
OK
NG



OK

11.PERFORM PM FORCED REGENERATION

NG

14.ADJUST ENGINE OIL LEVEL
11.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.



Result:
Result Proceed to
Manual forced regeneration completed normally A
Manual forced regeneration does not complete normally B



A

12.CHECK DTC OUTPUT

B

13.CHECK DTC OUTPUT
12.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

13.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Perform the inspection procedure for the output DTCs.


Result:
Proceed to
NEXT



NEXT

GO TO DTC CHART

14.ADJUST ENGINE OIL LEVEL
a.

Adjust the engine oil quantity according so that it is within the stipulated value.

Change the oil if it is dirty.


Result:
Proceed to
NEXT



NEXT

23.CHECK DTC OUTPUT
15.REPLACE FRONT EXHAUST PIPE ASSEMBLY
a.

Replace the front exhaust pipe assembly.

Click hereEngine / Hybrid System>N04C-WA (EXHAUST)>EXHAUST PIPE>REMOVAL


Result:
Proceed to
NEXT



NEXT

23.CHECK DTC OUTPUT
16.REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 3 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

23.CHECK DTC OUTPUT
17.REPAIR OR REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the No. 3 exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 3 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

23.CHECK DTC OUTPUT
18.REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Replace the turbocharger sub-assembly.

Click hereEngine / Hybrid System>N04C-WA (INTAKE)>TURBOCHARGER>REMOVAL


Result:
Proceed to
NEXT



NEXT

23.CHECK DTC OUTPUT
19.REPLACE EGR VALVE ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

23.CHECK DTC OUTPUT
20.ADJUST EXHAUST RETARDER ASSEMBLY
a.

Adjust the butterfly opening of the exhaust retarder assembly.

Click hereBrake>EXHAUST BRAKE>EXHAUST BRAKE RETARDER>REASSEMBLY


Result:
Proceed to
NEXT



NEXT

23.CHECK DTC OUTPUT
21.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

23.CHECK DTC OUTPUT
22.REPAIR OR REPLACE EXHAUST PIPE
a.

Repair the exhaust pipe.

HINT:

Replace it as needed.



Result:
Proceed to
NEXT



NEXT

23.CHECK DTC OUTPUT
23.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END