Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P268A  Fuel Injector Calibration Not Learned/Programmed  P2696  Injector Data Incompatible  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P268A Fuel Injector Calibration Not Learned/Programmed Diagnosis Condition:

Ignition switch ON


Malfunction Status:

The condition that the correction data was not written in the ECM continues for at least 2 seconds


Malfunction Duration:

2 seconds or more


ECM Class B2 DTC stored
P2696 Injector Data Incompatible Diagnosis Condition:

Ignition switch ON


Malfunction Status:

Corrected data (127 or higher, or -128 or lower) continues to write in the ECM for at least 2 seconds.


Malfunction Duration:

2 seconds or more


ECM Class B2 DTC stored

MONITOR DESCRIPTION

The fuel injection quantity is controlled by operation of the injector magnetic valve according to the injector valve open interval instructions from the ECM. In order to correct for injector manufacturing variations, however, a variation correction value (injector correction value) is measured, and then written into the ECM, during the injector manufacturing process.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P268A
P2696
Ignition switch ON for 2 seconds or more

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK INJECTOR REPLACE RECORD
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / Injector Compensation.


d.

Check if the compensation code of the installed injector matches the read compensation code.

OK:

Compensation code of installed injector matches read compensation code.



Result:
Proceed to
OK
NG



OK

2.CHECK DTC OUTPUT

NG

5.REGISTER INJECTOR COMPENSATION CODE
2.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P268A or P2696 are output A
DTCs are not output B




A

3.REPLACE ECM

B

END

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

5.REGISTER INJECTOR COMPENSATION CODE
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / Injector Compensation.


d.

Write the compensation code of the installed injector.


Result:
Proceed to
NEXT



NEXT

2.CHECK DTC OUTPUT