Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  U010A  Lost Communication with Exhaust Gas Recirculation Control Module "A"  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U010A Lost Communication with Exhaust Gas Recirculation Control Module "A" Diagnosis Condition:
·

Ignition switch ON

·

ECM power supply voltage is in the range of 10 V to 16 V


Malfunction Status:

The ECM does not receive CAN data from the EGR control for 3 seconds or more


Malfunction Duration:

3 seconds or more


·

EGR valve assembly

·

Harness or connector

·

ECM


Class A DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
U010A Ignition switch ON for 3 seconds or more

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

According to the display on the GTS, select "Health Check".


e.

Check for currently output system DTCs.

Result:
Result Proceed to
DTC U010A is output A
2 or more of the following DTCs are simultaneously output: U0073, U010A, U010C, U010E, U029D, U029E, U02A2 and U02A3 and urea system DTCs U010031 and U02A231 B
DTCs are not output C




A

2.CHECK CONNECTOR CONNECTION CONDITION (EGR VALVE ASSEMBLY)

B

C

2.CHECK CONNECTOR CONNECTION CONDITION (EGR VALVE ASSEMBLY)
a.

Check the connector connection for the EGR valve assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK EGR VALVE ASSEMBLY (POWER SOURCE CIRCUIT)

NG

11.CONNECT SECURELY
3.CHECK EGR VALVE ASSEMBLY (POWER SOURCE CIRCUIT)
a.
A407247C12
0.375,0.885 0.771,1.177 0.396,0.292 0.948,1.865 1.458,1.219 true 2.417,1.833 1.583,1.021 true 0.438,0.969 1.042,1.26 0.604,0.292 10 false B48 0.844,1.906 1.302,2.104 0.458,0.198 10 false +B 2.438,1.906 2.896,2.104 0.458,0.198 10 false E 0.125,0.156 0.583,0.354 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to EGR Valve Assembly)


Disconnect the EGR valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B48-4 (+B) - B48-1 (E) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS OR CONNECTOR

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS OR CONNECTOR
a.
A407247C13
0.375,0.885 0.771,1.177 0.396,0.292 0.906,1.854 1.667,1.198 true 2.615,1.813 1.781,1.052 true 0.448,0.948 1.052,1.24 0.604,0.292 10 false B48 0.844,1.906 1.74,2.104 0.896,0.198 10 false CANH 2.521,1.896 3.313,2.104 0.792,0.208 10 false CANL 0.125,0.156 0.583,0.354 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to EGR Valve Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the EGR valve assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-5 (CANH) - B48-2 (CANL) Ignition switch off 54 to 69 Ω
Positive (+) battery terminal - B48-5 (CANH) Ignition switch off 6 kΩ or higher
Positive (+) battery terminal - B48-2 (CANL)
B48-5 (CANH) - Body ground Ignition switch off 200 Ω or higher
B48-2 (CANL) - Body ground



Result:
Proceed to
OK
NG



OK

5.REPLACE EGR VALVE ASSEMBLY

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE EGR VALVE ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read Current DTCs.

Result:
Result Proceed to
DTC U010A is output A
DTCs are not output B




A

7.REPLACE ECM

B

END

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
8.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
11.CONNECT SECURELY
a.

Connect securely the EGR valve assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT