Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0016  Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0016 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V

·

Engine speed is in the range from 450 to 1000 rpm.

·

Engine coolant temperature is 50°C (122°F) or higher.

·

A difference between an actual engine speed and a target engine speed is 20 rpm or less.


Malfunction Status:

A phase difference between the engine speed main sensor (crankshaft position sensor) pulse and engine speed sub sensor (camshaft position sensor) pulse remains 10° or more.


Malfunction Duration:

1 second or more


·

Camshaft drive gear

·

Flywheel sub-assembly

·

Crankshaft position sensor

·

Camshaft position sensor


Class A DTC stored

MONITOR DESCRIPTION

A407889E01
3.417,0.083 4.031,0.281 0.615,0.198 10 false 720° 6.458,0.115 7.073,0.313 0.615,0.198 10 false 5V/DIV. 6.604,1.135 7.115,1.333 0.51,0.198 10 false GND 6.615,1.74 7.125,1.938 0.51,0.198 10 false GND 3.375,2.458 4.188,2.677 0.813,0.219 10 false 20 ms/DIV. 0.385,1.75 0.698,1.948 0.313,0.198 10 false NE 0.448,1.115 0.76,1.313 0.313,0.198 10 false G

A phase difference (deviation) between the crankshaft position sensor pulse and camshaft position sensor pulse is diagnosed.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0016 Idle the engine for 5 seconds after warming up the engine (the engine coolant temperature is 50°C (122°F) or higher).


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CAMSHAFT DRIVE GEAR
a.

Check the camshaft drive gear installation condition.


OK:

Camshaft drive gear is installed correctly.


Result:
Proceed to
OK
NG



OK

2.CHECK FLYWHEEL SUB-ASSEMBLY

NG

6.REPAIR OR REPLACE CAMSHAFT DRIVE GEAR
2.CHECK FLYWHEEL SUB-ASSEMBLY
a.

Check the flywheel sub-assembly installation condition.


OK:

Flywheel sub-assembly is installed correctly.


Result:
Proceed to
OK
NG



OK

3.CHECK CRANKSHAFT POSITION SENSOR AND CAMSHAFT POSITION SENSOR

NG

5.REPAIR OR REPLACE FLYWHEEL SUB-ASSEMBLY
3.CHECK CRANKSHAFT POSITION SENSOR AND CAMSHAFT POSITION SENSOR
a.

Check the crankshaft position sensor and camshaft position sensor installation condition.


OK:

The crank position sensor is installed correctly.


Result:
Proceed to
OK
NG



OK

7.CHECK DTC OUTPUT

NG

4.REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR AND CAMSHAFT POSITION SENSOR
4.REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR AND CAMSHAFT POSITION SENSOR


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
5.REPAIR OR REPLACE FLYWHEEL SUB-ASSEMBLY
a.

Repair or replace the flywheel sub-assembly.

HINT:

Change it as needed.



Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
6.REPAIR OR REPLACE CAMSHAFT DRIVE GEAR
a.

Repair or replace the camshaft drive gear.

HINT:

Change it as needed.



Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END