Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0336  Crankshaft Position Sensor "A" Circuit Range/Performance  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

Engine speed of 0 rpm or more


Malfunction Status:

With the engine running at 600 rpm, crankshaft position sensor does not detect pulses for continuous 1 second or longer.


Malfunction Duration:

1 seconds or more (engine speed is 600 rpm or higher)


·

Crankshaft position sensor

·

Harness or connector

·

ECM


Class A DTC stored
P0336 Crankshaft Position Sensor "A" Circuit Range/Performance Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V

·

Engine speed of 450 rpm or more


Malfunction Status:

Make a judgment when the abnormal number of crankshaft position sensor pulses (not 56 pulses) per engine revolution is continuously detected. For example, 63 seconds at 600 rpm


Malfunction Duration:

63 seconds or more (engine speed is 600 rpm or higher)


·

Crankshaft position sensor

·

Harness or connector

·

ECM


Class A DTC stored

MONITOR DESCRIPTION

The crankshaft position sensor consistently measures pulses from the crankshaft position sensor.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0335 After warming up engine, idle engine for 1 seconds or more.
P0336 After warming up engine, idle engine for 63 seconds or more.


WIRING DIAGRAM

A407166E02
0.719,4.052 2.448,4.302 1.729,0.25 10 false Camshaft Position Sensor 0.729,1.938 2.719,2.156 1.99,0.219 10 false Crankshaft Position Sensor 0.729,1.76 1.042,1.958 0.313,0.198 10 false B5 0.74,3.854 1.052,4.052 0.313,0.198 10 false k2 1.979,1.271 2.292,1.469 0.313,0.198 10 false 1 1.969,0.75 2.281,0.948 0.313,0.198 10 false 2 5.479,0.844 5.844,1.042 0.365,0.198 10 false NE+ 5.479,1.354 5.844,1.552 0.365,0.198 10 false NE- 5.479,1.885 5.844,2.083 0.365,0.198 10 false SNE 5.479,2.438 5.844,2.635 0.365,0.198 10 false VCG 5.469,2.979 5.833,3.177 0.365,0.198 10 false G+ 5.469,3.479 5.833,3.677 0.365,0.198 10 false E5 5.052,3.479 5.625,3.677 0.573,0.198 10 false B142 5.135,0.667 5.5,0.865 0.365,0.198 10 false 84 5.094,1.167 5.458,1.365 0.365,0.198 10 false 106 5.135,1.677 5.5,1.875 0.365,0.198 10 false 92 5.146,2.229 5.51,2.427 0.365,0.198 10 false 67 5.104,2.771 5.469,2.969 0.365,0.198 10 false 108 5.146,3.281 5.51,3.479 0.365,0.198 10 false 89 4.698,2.948 5.115,3.146 0.417,0.198 10 false E-73 4.708,0.854 5.125,1.052 0.417,0.198 10 false E-52 4.708,1.375 5.125,1.573 0.417,0.198 10 false E-72 4.708,1.875 5.125,2.073 0.417,0.198 10 false E-75 4.708,2.417 5.125,2.615 0.417,0.198 10 false E-53 4.708,3.458 5.125,3.656 0.417,0.198 10 false E-54 1.969,2.833 2.281,3.031 0.313,0.198 10 false 1 1.99,3.333 2.281,3.542 0.292,0.208 10 false 2 1.969,2.302 2.26,2.51 0.292,0.208 10 false 3 5.906,4.021 6.688,4.302 0.781,0.281 10 false ECM 5.063,2.948 5.615,3.146 0.552,0.198 10 false B142 5.063,2.427 5.521,2.625 0.458,0.198 10 false B142 5.063,1.865 5.521,2.052 0.458,0.188 10 false B142 5.063,1.365 5.542,1.563 0.479,0.198 10 false B142 5.052,0.854 5.552,1.052 0.5,0.198 10 false B142 1.656,2.427 2.021,2.625 0.365,0.198 10 false VG 1.656,2.948 2.021,3.146 0.365,0.198 10 false G1 1.656,3.458 2.021,3.656 0.365,0.198 10 false G- 1.573,0.854 1.938,1.052 0.365,0.198 10 false NE- 1.573,1.344 1.938,1.542 0.365,0.198 10 false NE+

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P0335 is output A
DTC P0336 is output B




A

2.CHECK CONNECTOR CONNECTION CONDITION (CRANKSHAFT POSITION SENSOR CONNECTOR)

B

14.CHECK FLYWHEEL ASSEMBLY
2.CHECK CONNECTOR CONNECTION CONDITION (CRANKSHAFT POSITION SENSOR CONNECTOR)
a.

Check the connector connection for the crankshaft position sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK CRANKSHAFT POSITION SENSOR

NG

13.CONNECT SECURELY
3.CHECK CRANKSHAFT POSITION SENSOR
a.

Check the installation of the crankshaft position sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the crankshaft position sensor.


Result:
Proceed to
OK
NG



OK

4.INSPECT CRANKSHAFT POSITION SENSOR

NG

12.REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR
4.INSPECT CRANKSHAFT POSITION SENSOR

Result:
Proceed to
OK
NG



OK

5.INSPECT CRANKSHAFT POSITION SENSOR (POWER SOURCE)

NG

11.REPLACE CRANKSHAFT POSITION SENSOR
5.INSPECT CRANKSHAFT POSITION SENSOR (POWER SOURCE)
a.
A449991C02
0.635,0.938 1.052,1.219 0.417,0.281 2.344,1.719 1.99,1.25 true 1.229,1.688 1.646,1.271 true 0.156,0.167 0.469,0.365 0.313,0.198 10 false *a 0.76,0.99 1.073,1.188 0.313,0.198 10 false B5 2.333,1.729 2.646,1.927 0.313,0.198 10 false NE- 0.969,1.688 1.281,1.885 0.313,0.198 10 false NE+
*a Front view of wire harness connector
(to Crankshaft Position Sensor)


Disconnect the crankshaft position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B5-1 (NE+) - B5-2 (NE-) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

8.CHECK DTC OUTPUT

NG

6.CHECK HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
6.CHECK HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-52 - Body ground and other terminals Always 10 kΩ or higher
E-72 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Connect the crankshaft position sensor connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-52 - E-72 Always (20°C) 108.5 to 142.5 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK DTC OUTPUT

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0335 is output A
DTCs are not output B




A

9.REPLACE ECM

B

END

9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

28.CHECK DTC OUTPUT
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

28.CHECK DTC OUTPUT
11.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

28.CHECK DTC OUTPUT
12.REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR
a.

Repair or replace the crankshaft position sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the crankshaft position sensor.



Result:
Proceed to
NEXT



NEXT

28.CHECK DTC OUTPUT
13.CONNECT SECURELY
a.

Connect securely the crankshaft position sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

28.CHECK DTC OUTPUT
14.CHECK FLYWHEEL ASSEMBLY
a.

Check if there is no blockage in the encoder slit of the flywheel assembly.


Result:
Proceed to
OK
NG



OK

15.CHECK CONNECTOR CONNECTION CONDITION (CRANKSHAFT POSITION SENSOR CONNECTOR)

NG

27.CLEAN FLYWHEEL ASSEMBLY
15.CHECK CONNECTOR CONNECTION CONDITION (CRANKSHAFT POSITION SENSOR CONNECTOR)
a.

Check the connector connection for the crankshaft position sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

16.CHECK CRANKSHAFT POSITION SENSOR

NG

26.CONNECT SECURELY
16.CHECK CRANKSHAFT POSITION SENSOR
a.

Check the installation of the crankshaft position sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the crankshaft position sensor.


Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

25.REPAIR OR REPLACE CRANK POSITION SENSOR
17.CHECK HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Turn the ignition switch off.


b.

Connect the crankshaft position sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-52 - B5-2 (NE-) Always Below 2 Ω
E-72 - B5-1 (NE+) Always Below 2 Ω



Result:
Proceed to
OK
NG


A449991C02
0.635,0.938 1.052,1.219 0.417,0.281 2.344,1.719 1.99,1.25 true 1.229,1.688 1.646,1.271 true 0.156,0.167 0.469,0.365 0.313,0.198 10 false *a 0.76,0.99 1.073,1.188 0.313,0.198 10 false B5 2.333,1.729 2.646,1.927 0.313,0.198 10 false NE- 0.969,1.688 1.281,1.885 0.313,0.198 10 false NE+
*a Front view of wire harness connector
(to Crankshaft Position Sensor)



OK

18.CHECK HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

24.REPAIR OR REPLACE HARNESS OR CONNECTOR
18.CHECK HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E52 - Body ground and other terminals Always 10 kΩ or higher
E-72 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK CRANKSHAFT POSITION SENSOR

NG

23.REPAIR OR REPLACE HARNESS OR CONNECTOR
19.CHECK CRANKSHAFT POSITION SENSOR
A407888E01
2.75,0.104 3.427,0.292 0.677,0.188 10 false 5 V/DIV. 3.063,1.021 3.427,1.229 0.365,0.208 10 false GND 1.438,1.917 2.323,2.156 0.885,0.24 10 false 20 ms/DIV.

a.

Connect the crankshaft position sensor connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.

Start the engine.


d.

Measure the signal voltage between the terminals and ECM.

Standard Voltage:
Tester Connection Condition Specified Condition
E-52 - E-72 Idling 56 pulses for each revolution



A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


Result:
Proceed to
OK
NG



OK

20.CHECK DTC OUTPUT

NG

22.REPLACE CRANKSHAFT POSITION SENSOR
20.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0336 is output A
DTCs are not output B




A

21.REPLACE ECM

B

END

21.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

28.CHECK DTC OUTPUT
22.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

28.CHECK DTC OUTPUT
23.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

28.CHECK DTC OUTPUT
24.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

28.CHECK DTC OUTPUT
25.REPAIR OR REPLACE CRANK POSITION SENSOR
a.

Repair or replace the crank position sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the crankshaft position sensor.



Result:
Proceed to
NEXT



NEXT

28.CHECK DTC OUTPUT
26.CONNECT SECURELY
a.

Connect securely the crankshaft position sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

28.CHECK DTC OUTPUT
27.CLEAN FLYWHEEL ASSEMBLY
a.

Clean the flywheel assembly.

HINT:

Repair if needed.



Result:
Proceed to
NEXT



NEXT

28.CHECK DTC OUTPUT
28.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END