Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0117  Engine Coolant Temperature Sensor 1 Circuit Low  P0118  Engine Coolant Temperature Sensor 1 Circuit High  P011A  Engine Coolant Temperature Sensor 1/2 Correlation  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0117 Engine Coolant Temperature Sensor 1 Circuit Low Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Output of the sensor remains at 0.1 V (122°C (251.6°F)) or less for 3 seconds or longer.


Malfunction Duration:

3 seconds or more


·

Engine coolant temperature sensor

·

Harness or connector

·

ECM


Class A DTC stored
P0118 Engine Coolant Temperature Sensor 1 Circuit High Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Output of the sensor remains at 4.77 V (-37°C (-34.6°F)) or greater for 3 seconds or longer.


Malfunction Duration:

3 seconds or more


·

Engine coolant temperature sensor

·

Harness or connector

·

ECM


Class A DTC stored
P011A Engine Coolant Temperature Sensor 1/2 Correlation Diagnosis Condition:
·

Engine speed is at least 500 rpm or engine is stopped.

·

Battery voltage is in the range of 10 V to 16 V


Malfunction Status:
·

If coolant temperature is low with respect to the calculated calorie.

·

If the intake air temperature is 15°C (59°F) or more higher than the coolant temperature during the engine is in operation.


Malfunction Duration:

-


·

Engine coolant temperature sensor

·

ECM


Class A DTC stored

MONITOR DESCRIPTION

·

P0117, P0118:

The Engine coolant temperature sensor installed to the thermostat case consistently measures the engine coolant temperature.

·

P011A:

Although some exhaust gas components operate after the engine coolant temperature has risen to some degree (engine warm up), when an engine coolant temperature sensor reads a value lower than the actual temperature, it means it is not working properly. Diagnosis is therefore required to detect if there is something wrong with the characteristics of the engine coolant temperature sensor.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0117
P0118
Ignition switch ON for 8 seconds or more.
P011A Start the engine for 15 seconds or more.


WIRING DIAGRAM

A407162E22
0.271,2.146 2.948,2.427 2.677,0.281 10 false Engine Coolant Temperature Sensor 0.302,1.906 0.615,2.104 0.313,0.198 10 false k1 1.917,1.333 2.229,1.531 0.313,0.198 10 false 2 1.917,0.771 2.229,0.969 0.313,0.198 10 false 1 4.823,0.906 5.219,1.104 0.396,0.198 10 false B142 4.823,1.5 5.219,1.729 0.396,0.229 10 false B142 1.51,0.823 2.021,1.021 0.51,0.198 10 false THW 5.25,1.51 5.76,1.708 0.51,0.198 10 false E2 4.938,0.719 5.25,0.917 0.313,0.198 10 false 6 4.906,1.302 5.219,1.5 0.313,0.198 10 false 85 4.458,0.917 4.771,1.115 0.313,0.198 10 false E-66 4.458,1.5 4.875,1.698 0.417,0.198 10 false M-54 5.646,2.417 6.438,2.688 0.792,0.271 10 false ECM 5.25,0.906 5.76,1.104 0.51,0.198 10 false THW 1.625,1.396 2.135,1.594 0.51,0.198 10 false E2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (ENGINE COOLANT TEMPERATURE SENSOR)
a.

Check the connector connection for the engine coolant temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK ENGINE COOLANT TEMPERATURE SENSOR

NG

13.CONNECT SECURELY
2.CHECK ENGINE COOLANT TEMPERATURE SENSOR
a.

Check the installation of the engine coolant temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the engine coolant temperature sensor.


Result:
Proceed to
OK
NG



OK

3.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

12.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
3.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

4.CHECK ENGINE COOLANT TEMPERATURE SENSOR

NG

11.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
4.CHECK ENGINE COOLANT TEMPERATURE SENSOR
A256065C04
0.552,0.948 1.042,1.24 0.49,0.292 1.229,1.552 1.625,1.104 true 2.24,1.542 1.833,1.104 true 0.229,0.167 0.563,0.479 0.333,0.313 10 false *a 0.75,1.031 0.938,1.188 0.188,0.156 10 false k1 0.906,1.583 1.677,1.781 0.771,0.198 10 false THW 2.229,1.573 3,1.771 0.771,0.198 10 false E2
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor)


a.

Disconnect the engine coolant temperature sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
k1-1 (THW) - k1-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

7.CHECK DTC OUTPUT

NG

5.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
5.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Disconnect the engine coolant temperature sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405886C09
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C05
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-66 - Body ground and other terminals Always 10 kΩ or higher
M-54 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Turn the ignition switch off.


b.

Connect the ECM connector.


c.

Connect the engine coolant temperature sensor connector.


d.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405886C09
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C05
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-66 - M-54 Always (20°C) 2.32 to 2.59 kΩ
E-66 - M-54 Always (80°C) 0.310 to 0.326 kΩ



Result:
Proceed to
OK
NG



OK

7.CHECK DTC OUTPUT

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0117, P0118 or P011A is output A
DTCs are not output B




A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
11.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
12.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Repair or replace the engine coolant temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the engine coolant temperature sensor.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
13.CONNECT SECURELY
a.

Connect securely the engine coolant temperature sensor.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
14.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END