Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0122  Throttle/Pedal Position Sensor/Switch "A" Circuit Low  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0122 Throttle/Pedal Position Sensor/Switch "A" Circuit Low Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Throttle position sensor remains at 0.2 V or less for 3 seconds or longer.


Malfunction Duration:

3 seconds or more


·

Throttle position sensor (built into diesel throttle body)

·

Harness or connector

·

ECM


Class B1 DTC stored
P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Output of the throttle position sensor remains at 4.8 V or less for 3 seconds or longer.


Malfunction Duration:

3 seconds or more


·

Throttle position sensor (built into diesel throttle body)

·

Harness or connector

·

ECM


Class B1 DTC stored

MONITOR DESCRIPTION

·

The throttle controls valves steplessly to control boost pressure and intake air volume.

·

Inside the diesel throttle body, a sensor designed to detect a travel of the valve consistently monitors a measurement reading and an actual opening.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0122
P0123
Ignition switch ON for 3 seconds or more.


WIRING DIAGRAM

A407156E10
2.052,1.083 2.51,1.281 0.458,0.198 10 false VTA 2.125,1.458 2.583,1.656 0.458,0.198 10 false VC 2.135,1.833 2.594,2.031 0.458,0.198 10 false E2 0.667,2.25 1.125,2.448 0.458,0.198 10 false B27 2.479,0.948 2.938,1.146 0.458,0.198 10 false 3 2.479,1.333 2.938,1.531 0.458,0.198 10 false 1 2.479,1.708 2.938,1.906 0.458,0.198 10 false 2 5.083,0.885 5.542,1.083 0.458,0.198 10 false 4 5.031,1.292 5.49,1.49 0.458,0.198 10 false 68 5.042,1.677 5.5,1.875 0.458,0.198 10 false 90 4.615,1.104 5.073,1.302 0.458,0.198 10 false E-62 4.594,1.479 5.052,1.677 0.458,0.198 10 false M-51 4.615,1.854 5.073,2.052 0.458,0.198 10 false E-77 5.385,1.083 5.844,1.281 0.458,0.198 10 false VTA1 5.385,1.49 5.844,1.688 0.458,0.198 10 false VC 5.396,1.865 5.854,2.063 0.458,0.198 10 false E4 5.792,2.708 6.25,2.906 0.458,0.198 10 false ECM 0.625,2.479 4.448,2.677 3.823,0.198 10 false Diesel Throttle Body (Throttle Position Sensor) 4.958,1.104 5.417,1.302 0.458,0.198 10 false B142 4.969,1.479 5.427,1.677 0.458,0.198 10 false B142 4.969,1.854 5.427,2.052 0.458,0.198 10 false B142

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (THROTTLE POSITION SENSOR)
a.

Check the connector connection for the throttle position sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.INSPECT THROTTLE POSITION SENSOR

NG

12.CONNECT SECURELY
2.INSPECT THROTTLE POSITION SENSOR
A407246C08
0.542,1.052 0.969,1.333 0.427,0.281 1.292,1.698 1.521,1.26 true 2.083,1.75 1.75,1.271 true 0.208,0.188 0.521,0.385 0.313,0.198 10 false *a 0.635,1.104 0.948,1.302 0.313,0.198 10 false B27 1.177,1.75 1.49,1.948 0.313,0.198 10 false VC 2.104,1.75 2.417,1.948 0.313,0.198 10 false E2
*a Front view of wire harness connector
(to Throttle Position Sensor)


a.

Disconnect the throttle position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B27-1 (VC) - B27-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.INSPECT THROTTLE POSITION SENSOR

NG

10.CHECK HARNESS OR CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)
3.INSPECT THROTTLE POSITION SENSOR
A407246C09
0.51,0.906 0.906,1.177 0.396,0.271 1.396,1.75 1.667,1.271 true 2.167,1.719 1.896,1.26 true 0.594,0.958 0.906,1.156 0.313,0.198 10 false B27 1.156,1.813 1.469,2.01 0.313,0.198 10 false E2 2.104,1.844 2.417,2.042 0.313,0.198 10 false VTA 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Throttle Position Sensor)


a.

Disconnect the throttle position sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B27-3 (VTA) - B27-2 (E2) Ignition switch off 25 to 35 kΩ



Result:
Proceed to
OK
NG



OK

4.INSPECT THROTTLE POSITION SENSOR

NG

9.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
4.INSPECT THROTTLE POSITION SENSOR
A407639C02
0.125,0.135 0.438,0.333 0.313,0.198 10 false *a
*a Component with harness connected
(Throttle Position Sensor)


a.

Disconnect the throttle position sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 1 Always 180 Ω
3 - 2 Always 3 kΩ
2 - 1 Always 3 kΩ



Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT

NG

7.REPLACE DIESEL THROTTLE BODY
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 70°C (158°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read the DTCs.

Result:
Result Proceed to
DTC P0122 or P0123 is output A
DTCs are not output B




A

6.REPLACE ECM

B

END

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
7.REPLACE DIESEL THROTTLE BODY

Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
8.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 70°C (158°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

9.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connectors.


b.

Disconnect the throttle position sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-62 - Body ground and other terminals Always 10 kΩ or higher
E-77 - Body ground and other terminals Always 10 kΩ or higher
M-51 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS OR CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.CHECK HARNESS OR CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the ECM connectors.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-62 - M-51 Ignition switch off 2 Ω or higher
M-51 - E-77 Ignition switch off 3 kΩ or higher
E-62 - E77 Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT THROTTLE POSITION SENSOR

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
12.CONNECT SECURELY
a.

Connect securely the throttle position sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT