Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

Engine speed is 1100 rpm or more.


Malfunction Status:

The starter signal remains ON for 30 seconds or more


Malfunction Duration:

30 seconds or more


·

Harness or connector

·

ECM


Class C DTC stored

MONITOR DESCRIPTION

ECM detects the starter signal while the engine is running (START position signal).

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0617 Drive at an engine speed of 1200 rpm or higher for 30 seconds or more.

WIRING DIAGRAM

A451040E02
6.271,2.604 6.75,2.875 0.479,0.271 10 false ECM 0.854,4.771 1.469,4.969 0.615,0.198 10 false Battery 0.729,3.573 1.344,3.771 0.615,0.198 10 false FL-MAIN 3.448,4.521 4.76,4.729 1.313,0.208 10 false Starter Assembly 3,4.156 3.385,4.333 0.385,0.177 10 false C11 3.854,3.813 4.24,3.99 0.385,0.177 10 false B99 4,3.646 4.385,3.823 0.385,0.177 10 false 1 3.083,3.99 3.469,4.167 0.385,0.177 10 false 1 4.01,3.219 4.396,3.396 0.385,0.177 10 false 3 4.021,2.323 4.406,2.5 0.385,0.177 10 false 5 4.458,3.219 4.844,3.396 0.385,0.177 10 false 2 4.458,2.333 4.844,2.51 0.385,0.177 10 false 1 2.49,2.365 3.469,2.531 0.979,0.167 10 false ST NO.1 1.229,2.365 2.208,2.531 0.979,0.167 10 false R/B NO. 2-B 4.677,2.813 4.969,3.01 0.292,0.198 10 false ST 6.146,0.479 6.552,0.667 0.406,0.188 10 false STA 5.771,0.302 6.177,0.49 0.406,0.188 10 false 4 3.354,0.656 4.333,0.823 0.979,0.167 10 false ST NO.2 1.5,1.427 4.24,1.635 2.74,0.208 10 false Park/Neutral Position Switch Assembly*1 1.531,1.26 2.51,1.427 0.979,0.167 10 false B135 4.438,0.802 4.74,1 0.302,0.198 10 false 10 4.458,1.813 4.76,2.01 0.302,0.198 10 false 6 3.656,5.01 5.813,5.229 2.156,0.219 10 false *1: for Automatic transmission 3.656,5.292 5.521,5.521 1.865,0.229 10 false *2: for Manual transmission 4.198,1.938 4.604,2.125 0.406,0.188 10 false *1 4.583,0.344 4.99,0.531 0.406,0.188 10 false *2 4.177,0.719 4.583,0.906 0.406,0.188 10 false *1 5.219,0.469 5.625,0.656 0.406,0.188 10 false V-12 5.656,0.469 6.063,0.656 0.406,0.188 10 false A115 1.552,0.75 2.531,0.917 0.979,0.167 10 false J63 1.552,0.906 3.771,1.271 2.219,0.365 10 false Ignition Switch Assembly 2.708,0.396 3.688,0.563 0.979,0.167 10 false ST2 3.063,0.396 4.042,0.563 0.979,0.167 10 false 9 1.938,0.396 2.917,0.563 0.979,0.167 10 false AM2 1.708,0.396 2.688,0.563 0.979,0.167 10 false 12 1.135,0.615 2.115,0.781 0.979,0.167 10 false AM2 0.719,1.25 1.698,1.417 0.979,0.167 10 false J/B-B 3.354,4.167 3.74,4.344 0.385,0.177 10 false B 3.885,4.01 4.271,4.188 0.385,0.177 10 false ST 4.219,1.583 4.604,1.76 0.385,0.177 10 false B 4.208,1.01 4.594,1.188 0.385,0.177 10 false L

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STARTER SIGNAL)
A405886C10
1.479,0.125 1.896,0.396 0.417,0.271 0.177,0.167 0.49,0.365 0.313,0.198 10 false *a 1.635,0.188 1.948,0.385 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


a.

Turn the ignition switch off.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.

Disconnect the ignition or starter switch assembly connector. (Manual Transmission Models)


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V-12 - Body ground Ignition switch ON Below 1 V



Result:
Result Proceed to
OK (Manual Transmission Models) A
OK (Automatic Transmission Models) B
NG C



A

2.CHECK HARNESS AND CONNECTOR

B

5.REPLACE ECM

C

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK HARNESS AND CONNECTOR
a.

Turn the ignition switch off.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.

Connect the ignition or starter switch assembly.


d.

Turn the ignition switch to ON.


e.
A405886C10
1.479,0.125 1.896,0.396 0.417,0.271 0.177,0.167 0.49,0.365 0.313,0.198 10 false *a 1.635,0.188 1.948,0.385 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V-12 - V-40 Ignition switch off Below 1 V
V-12 - V-40 START 11 V or higher



f.
A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V-12 - V-60 Ignition switch ON Below 1 V
V-12 - V-60 START 11 V or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
4.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
a.

Replace the ignition or starter switch assembly.


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END