Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0643  Sensor Reference Voltage "A" Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0643 Sensor Reference Voltage "A" Circuit High Diagnosis Condition:
·

Above conditions continue for at least 5 seconds.

-

Ignition switch ON

-

Battery voltage is in the range of 10 V to 16 V



Malfunction Status:

Power supply voltage no greater than 4.5 V for at least 3 seconds.


Malfunction Duration:

3 seconds or more


·

Harness or connector

·

ECM


Class A DTC stored

MONITOR DESCRIPTION

Power is supplied to the sensor power supply 1 circuit.

(Fuel pressure sensor, No. 2 fuel pressure sensor, differential pressure sensor, manifold absolute pressure sensor, throttle position sensor, accelerator pedal position sensor)

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0643 Ignition switch ON for 8 seconds or more.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
A405886C09
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C17
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.

Disconnect the fuel pressure sensor connector.


d.

Disconnect the accelerator pedal assembly connector.


e.

Disconnect the differential pressure sensor connector.


f.

Disconnect the manifold absolute pressure sensor connector.


g.

Disconnect the throttle position sensor connector.


h.

Disconnect the No. 2 fuel pressure sensor connector.


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E-13 - Body ground and other terminals Ignition switch ON Below 1 V
V-50 - Body ground and other terminals Ignition switch ON Below 1 V
V-71 - Body ground and other terminals Ignition switch ON Below 1 V
M-51 - Body ground and other terminals Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK HARNESS AND CONNECTOR
A405886C09
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C17
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E-13 - E-56 Ignition switch ON 4.5 to 5.5 V
V-50 - V-45 Ignition switch ON 4.5 to 5.5 V
V-71 - V-46 Ignition switch ON 4.5 to 5.5 V
M-51 - E-77 Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

4.REPLACE ECM
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0643 is output A
DTCs are not output B




A

4.REPLACE ECM

B

5.CHECK DTC OUTPUT
4.REPLACE ECM
a.

Replace the ECM.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT