While the engine is being cranked, current flows from terminal ST2 of the ignition switch to the ST relay and also flows to terminal STA of the ECM (STA signal).
Refer to DTC P0617 (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>P0617).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check if the engine can be cranked.
| Result | Proceed to |
|---|---|
| Engine cannot be cranked | A |
| Engine can be cranked | B |
A
B
Inspect the ST relay assembly.
Click hereEngine / Hybrid System>N04C-UH (STARTING)>STARTER RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 2 relay block and junction block assembly.
Disconnect the ignition switch assembly connector.
Disconnect the ECM connector.
Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J63-9 (ST2) - V-12 | Always | Below 1 Ω |
| ST relay terminal 1 - V-12 | Always | Below 1 Ω |
| J63-9 (ST2) or V-12 - Body ground | Always | 10 kΩ or higher |
| ST relay terminal 1 or V-12 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly.
Click hereEngine / Hybrid System>N04C-UH (STARTING)>IGNITION SWITCH(w/ Tilt Steering Column)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 2 relay block and junction block assembly.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal 5 - Battery positive (+) terminal | Always | Below 1 Ω |
| ST relay terminal 3 - B12-1 (ST) | Always | Below 1 Ω |
| ST relay terminal 5 or Battery positive (+) terminal - Body ground | Always | 10 kΩ or higher |
| ST relay terminal 3 or B12-1 (ST) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the valve displayed on the GTS when the ignition switch is turned to ON and START position.
| Ignition Switch Condition | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 2 relay block and junction block assembly.
Disconnect the ignition switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J63-9 (ST2) - V12 | Always | Below 1 Ω |
| J63-9 (ST2) or V-12 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG