| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | Memory |
|---|---|---|---|---|---|---|
| P0562A2 | System Voltage Low System Voltage Low | Diagnosis Condition:
·
Ignition switch ON. Malfunction Status: ·
The battery voltage is less than 8.48 V. Malfunction Duration: ·
22 seconds or more. |
·
Open or short in DCU (emission control ECU assembly) circuit ·
DCU (emission control ECU assembly) |
Class B1 | AdBlue consumption warning light:
Comes on |
DTC stored |
Low voltage malfunction is detected in battery voltage (DCU (emission control ECU assembly) power circuit).
After having restored to the normal conditions.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0562A2 | Ignition switch ON for 22 seconds or more. |
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Check the connector connection and contact pressure of the DCU (emission control ECU assembly) connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Signal Check Harness No. 2 Lead Connector |
Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) and DCU (emission control ECU assembly) vehicle side harness.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-19 (+BU3) - E-41 (GND4) | Ignition switch ON | 9 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
| *a | Signal Check Harness No. 2 Lead Connector |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0562A2 is output | A |
| DTCs are not output | B |
A
B
Replace the DCU (emission control ECU assembly).
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the ECU power source circuit and if there are any malfunctions, repair or replace it.
| Proceed to |
|---|
| NEXT |
NEXT
Securely connect the DCU connector.
Repair parts as necessary.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.
Read the DTCs.
DTCs are not output
| Proceed to |
|---|
| NEXT |
NEXT