Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P204B64  Reductant Pressure Sensor Circuit Range/Performance Signal Plausibility Failure  


DESCRIPTION

The pressure sensor embedded in the urea pump is used to check the pressure in the urea solution piping.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P204B64 Reductant Pressure Sensor Circuit Range/Performance Signal Plausibility Failure Diagnosis Condition:
·

Urea solution is defrosted.

·

Urea injection quantity is within the specified range (in case of during urea injection).


Malfunction Status:
·

Output deviation of the pressure sensor (urea pump) is detected.


Malfunction Duration:
·

-


Pressure sensor (urea pump) Class A AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

Abnormality is detected in the pressure sensor located in the urea pump.


Reset condition

Procedure to turn off MIL and AdBlue consumption warning light by returning system to normal.

With the urea solution not frozen, start the engine.

When the exhaust gas temperature is 160°C (320°F) or more, the urea SCR system starts and diagnosis of the urea pump and urea injector assembly is performed. After diagnosis is complete, stop the engine.

Repeat the above procedure 3 times.

When the urea SCR system determines that it is normal after starting 1 time, the illuminated MIL remains illuminated and the AdBlue consumption warning light turns off. When the urea SCR system determines that it is normal after starting 3 times, the MIL turns off.


Procedure to turn off MIL and AdBlue consumption warning light after repairs.

After repairs are complete, connect the GTS and clear* the urea SCR system DTCs.

When the engine starts, check that the MIL illuminates and the AdBlue consumption warning light turns off. After 1 minute elapses, stop the engine. Start the engine again and check that the MIL turns off and the system returns to normal.

(*: The ECM malfunction information is not cleared, even if the urea SCR system DTCs are cleared. However, the command that caused the MIL to continuously illuminate is cleared.)



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P204B64 Perform the "Pressure Rising Diagnosis (Leak Test)" Utility to increase the pressure to 5 bar, and then wait for 1 minute or more.

CAUTION / NOTICE / HINT

NOTICE:
Handling urea solution
·

Wear protective equipment as necessary (protective glasses and gloves).

·

Do not dilute urea solution.

·

If urea solution contacts your eyes or skin, immediately wash the contacted area with a large amount of water and consult a doctor as necessary.

·

If urea solution dries, it deposits a white powder. Also, if urea solution contacts metals such as copper and aluminum for a long period of time, it may promote corrosion. Therefore, if urea solution is spilled, dampen a cloth or other item and wipe it up or rinse the area with cool or warm water.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (REDUCTANT PUMP PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Data List / Reductant Pump Pressure.


e.

Read the value.

OK:

-40.0 to 40.0 kPa



Result:
Proceed to
OK
NG



OK

2.INSPECT PRESSURE SENSOR (UREA PUMP)

NG

3.REPLACE PRESSURE SENSOR (UREA PUMP)
2.INSPECT PRESSURE SENSOR (UREA PUMP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Pressure Rising Diagnosis (Leak Test).


e.

Perform the Utility and check the Reductant Pump Pressure.


Result:
Result Proceed to
Reductant Pump Pressure is 4.5 to 5.5 bar A
Except above B



A

6.CLEAR DTC

B

3.REPLACE PRESSURE SENSOR (UREA PUMP)
3.REPLACE PRESSURE SENSOR (UREA PUMP)
a.

Replace the pressure sensor (urea pump).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.INSPECT DCU (EMISSION CONTROL ECU ASSEMBLY)
4.INSPECT DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Pressure Rising Diagnosis (Leak Test).


e.

Perform the Utility and check that "Pressure Rising Diagnosis (Leak Test)" completes normally.


OK:

"Pressure Rising Diagnosis (Leak Test)" completes normally.


Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

5.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
5.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P204B64)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P204B64)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END