Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P208B77  Reductant Pump "A" Control Performance/Stuck Off Commanded Position Not Reachable  


DESCRIPTION

The urea pump is used to send urea solution to the urea injector assembly.

The urea pump operates according to the command values from the DCU (emission control ECU assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P208B77 Reductant Pump "A" Control Performance/Stuck Off Commanded Position Not Reachable Diagnosis Condition:
·

Urea solution is defrosted.


Malfunction Status:
·

During operation, abnormality is detected with the energizing current value to the urea pump.


Malfunction Duration:
·

-


·

Urea pump

·

DCU (emission control ECU assembly)


Class A AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

Motor malfunction of urea pump is detected.


Reset condition

After having restored to the normal conditions.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P208B77 Perform the "Pressure Rising Diagnosis (Leak Test)" Utility to increase the pressure to 5 bar, and then maintain the pressure at 5 bar for 5 seconds or more.

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT UREA PUMP
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Reductant Pump Speed Check.


e.

Perform the Utility and check that "Reductant Pump Speed Check" completes normally.

OK:

"Reductant Pump Speed Check" completes normally.



Result:
Proceed to
OK
NG


HINT:

If an error message is displayed other than the messages below, perform the corrective action according to the error message, and then retry the test.

·

Reductant Pump Start Test has failed.

·

Reductant Pump Current is too high.

·

Reductant Pressure is high.




OK

5.CLEAR DTC

NG

2.REPLACE UREA PUMP
2.REPLACE UREA PUMP

Result:
Proceed to
NEXT



NEXT

3.INSPECT DCU (EMISSION CONTROL ECU ASSEMBLY)
3.INSPECT DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Pressure Rising Diagnosis (Leak Test).


e.

Perform the Utility and check that "Pressure Rising Diagnosis (Leak Test)" completes normally.

OK:

"Pressure Rising Diagnosis (Leak Test)" completes normally.



Result:
Proceed to
OK
NG



OK

5.CLEAR DTC

NG

4.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
4.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P208B77)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P208B77)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END