Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P20B914  Reductant Heater "A" Control Circuit Low Circuit Short to Ground or Open  P20BC12  Reductant Heater "A" Control Circuit High Circuit Short to Battery  


DESCRIPTION

The pipe heater prevents urea solution pipe freezing.

Disconnections and short circuits in the urea solution pipe heater are detected by the DCU (emission control ECU assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P20B914 Reductant Heater "A" Control Circuit Low Circuit Short to Ground or Open Diagnosis Condition:
·

During operation of the urea tube with heater assembly.


Malfunction Status:
·

The urea tube with heater assembly voltage is less than specified value.


Malfunction Duration:
·

3 seconds or more.


·

Open or short in urea tube with heater assembly circuit

·

Urea tube with heater assembly

·

DCU (emission control ECU assembly)


Class A AdBlue consumption warning light:
Comes on
DTC stored
P20BC12 Reductant Heater "A" Control Circuit High Circuit Short to Battery Diagnosis Condition:
·

During operation of the urea tube with heater assembly.


Malfunction Status:
·

The urea tube with heater assembly voltage is more than specified value.


Malfunction Duration:
·

3 seconds or more.


·

Open or short in urea tube with heater assembly circuit

·

Urea tube with heater assembly

·

DCU (emission control ECU assembly)


Class A AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

Voltage abnormality is detected in the urea tube with heater assembly.


Reset condition

After having restored to the normal conditions.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20B914 Ignition switch ON for 3 seconds or more.
P20BC12

WIRING DIAGRAM

A444341E01
5.26,2.031 6.729,2.417 1.469,0.385 10 false DCU (Emission Control ECU Assembly) 3.688,1.208 4.063,1.385 0.375,0.177 10 false HTR- 3.677,0.604 4.125,0.781 0.448,0.177 10 false HTR+ 4.229,0.615 4.542,0.792 0.313,0.177 10 false 1 4.208,1.198 4.521,1.375 0.313,0.177 10 false 2 5.083,0.542 5.396,0.719 0.313,0.177 10 false 3 5.042,1.135 5.354,1.313 0.313,0.177 10 false 22 5.375,0.729 5.688,0.906 0.313,0.177 10 false HTL 5.385,1.323 5.76,1.5 0.375,0.177 10 false EHTL 4.635,0.74 4.948,0.917 0.313,0.177 10 false E-3 4.594,1.323 4.906,1.5 0.313,0.177 10 false E-22 5,0.74 5.313,0.917 0.313,0.177 10 false P12 5,1.313 5.313,1.49 0.313,0.177 10 false P12 2.188,0.625 2.5,0.802 0.313,0.177 10 false 1 2.188,1.219 2.5,1.396 0.313,0.177 10 false 2 2.396,2 4.469,2.396 2.073,0.396 10 false Urea Tube with Heater Assembly (rear) 2.406,1.844 2.719,2.021 0.313,0.177 10 false P10 0.323,2 2.396,2.396 2.073,0.396 10 false Urea Tube with Heater Assembly (front)

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (UREA TUBE WITH HEATER ASSEMBLY (FRONT AND REAR))
a.

Check the connector connection and contact pressure of the urea tube with heater assembly (front and rear) connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.INSPECT UREA TUBE WITH HEATER ASSEMBLY (FRONT AND REAR)

NG

11.CONNECT SECURELY
2.INSPECT UREA TUBE WITH HEATER ASSEMBLY (FRONT AND REAR)
a.

Check that the urea tube with heater assembly (front and rear) is free of damage such as cracks (urea solution leaks, etc.).


OK:

Urea tube with heater assembly (front and rear) is free of damage such as cracks (urea solution leaks, etc.).


Result:
Proceed to
OK
NG



OK

3.INSPECT UREA TUBE WITH HEATER ASSEMBLY (FRONT AND REAR)

NG

10.REPLACE UREA TUBE WITH HEATER ASSEMBLY
3.INSPECT UREA TUBE WITH HEATER ASSEMBLY (FRONT AND REAR)
a.
A222598C02
0.143,0.104 0.336,0.292 0.193,0.188 10 *a
*a Component without harness connected
(Urea Tube with Heater Assembly [Rear])


Disconnect the urea tube with heater assembly (rear) connector on the vehicle side.

HINT:

Do not disconnect the urea tube with heater assembly (rear) connector on the urea tube with heater assembly (front) side.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C 1.57 to 1.93 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (UREA TUBE WITH HEATER ASSEMBLY - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

7.INSPECT UREA TUBE WITH HEATER ASSEMBLY (FRONT)
4.CHECK HARNESS AND CONNECTOR (UREA TUBE WITH HEATER ASSEMBLY - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


A179479C10
1.521,0.458 1.885,0.719 0.365,0.26 0.958,1.938 1.5,1.615 true 1.938,1.635 2.396,1.917 true 0.313,0.135 0.573,0.375 0.26,0.24 10 false *a 0.635,1.938 1.25,2.135 0.615,0.198 10 false HTR+ 2.438,1.927 3.052,2.125 0.615,0.198 10 false HTR- 1.583,0.51 2.198,0.708 0.615,0.198 10 false P10
*a Front view of wire harness connector
(to Urea Tube with Heater Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P10-1 (HTR+) - E-3 (HTL) Ignition switch off Below 1 Ω
P10-2 (HTR-) - E-22 (EHTL) Ignition switch off Below 1 Ω
E-3 (HTL) - Body ground Ignition switch off 10 kΩ or higher
E-22 (EHTL) - Body ground Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
7.INSPECT UREA TUBE WITH HEATER ASSEMBLY (FRONT)
a.
A222598C02
0.143,0.104 0.336,0.292 0.193,0.188 10 *a
*a Component without urea tube with heater assembly (rear) connected
(Urea Tube with Heater Assembly [Front])


Disconnect the urea tube with heater assembly (front) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C 1.00 to 1.24 Ω



Result:
Proceed to
OK
NG



OK

8.REPLACE UREA TUBE WITH HEATER ASSEMBLY (REAR)

NG

9.REPLACE UREA TUBE WITH HEATER ASSEMBLY (FRONT)
8.REPLACE UREA TUBE WITH HEATER ASSEMBLY (REAR)
a.

Replace the urea tube with heater assembly (rear).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA TUBE>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
9.REPLACE UREA TUBE WITH HEATER ASSEMBLY (FRONT)
a.

Replace the urea tube with heater assembly (front).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA TUBE>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
10.REPLACE UREA TUBE WITH HEATER ASSEMBLY
a.

Replace the urea tube with heater assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA TUBE>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
11.CONNECT SECURELY
a.

Securely connect the urea tube with heater assembly connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
12.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P20B914 OR P20BC12)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P20B914 OR P20BC12)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END