Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P20E865  Reductant Pressure Too Low Signal Has Too Few Transitions / Events  


DESCRIPTION

Urea solution line pressure depends on ejection of the urea pump.

Urea pump ejection is determined by value of the pressure sensor which is built in the urea pump.

A444329C02
3.313,1.26 3.448,1.26 3.448,1.26 3.917,2.281 true 3.594,1.031 3.75,1.031 3.75,1.031 4.24,2.083 true 3.906,0.833 4.021,0.833 4.021,0.833 4.615,2.26 true 4.208,0.625 4.385,0.625 4.385,0.625 4.729,2.281 true 2.854,2.115 3.031,2.115 3.031,2.115 3.438,2.344 true 2.833,1.719 3.01,1.719 3.01,1.719 3.583,2.271 true 0.354,0.25 0.49,0.25 0.49,0.25 1.292,0.802 true 2.115,0.167 1.969,0.167 1.969,0.167 1.5,0.917 true 0.323,1.719 0.458,1.719 0.458,1.719 0.719,0.969 true 1.521,2.563 1.833,2.719 0.313,0.156 10 false *1 2.802,3.104 3.115,3.26 0.313,0.156 10 false *2 3.625,3.063 3.938,3.219 0.313,0.156 10 false *3 4.281,2.656 4.594,2.813 0.313,0.156 10 false *4 3.135,1.188 3.448,1.344 0.313,0.156 10 false *5 3.448,0.948 3.76,1.104 0.313,0.156 10 false *6 2.667,1.635 2.979,1.792 0.313,0.156 10 false *7 4.052,0.542 4.365,0.698 0.313,0.156 10 false *8 3.458,2.677 3.771,2.833 0.313,0.156 10 false *9 2.604,2.021 2.938,2.219 0.333,0.198 10 false *10 6.073,2.365 6.469,2.615 0.396,0.25 10 false *11 3.75,0.75 4.063,0.906 0.313,0.156 10 false *7 1.542,1.542 2.01,1.698 0.469,0.156 10 false *11 0.115,1.646 0.427,1.802 0.313,0.156 10 false *9 2.156,0.073 2.469,0.229 0.313,0.156 10 false *a 0.167,0.188 0.479,0.344 0.313,0.156 10 false *b
*1 Muffler *2 Urea Injector Assembly
*3 Urea Tube with Heater Assembly *4 Urea Pump
*5 Pressure Sensor *6 Pump Motor
*7 Temperature Sensor *8 Level Sensor
*9 Urea Sensor Assembly *10 Urea Solution Quality Sensor
*11 Urea Tank - -
*a Harness Connector *b Pressure Line


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P20E865 Reductant Pressure Too Low Signal Has Too Few Transitions / Events Diagnosis Condition:
·

SCR inlet exhaust gas temperature is higher than 160°C (320°F).

·

Urea solution defrosting is done.

·

The time after starting pressurizing urea solution is 50 seconds or more.


Malfunction Status:
·

Abnormally low pressure is detected during filling mode, pressure rising mode or pressure keep mode.


Malfunction Duration:
·

-


·

Urea pump

·

Urea tube with heater assembly

·

Urea injector assembly

·

DCU (emission control ECU assembly)


Class A AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

Abnormal pressure in the urea solution pipe is detected.


Reset condition

After having restored to the normal conditions.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20E865 Perform the "Pressure Rising Diagnosis (Leak Test)" Utility to increase the pressure to 5 bar, and then wait for 2 minutes or more.

CAUTION / NOTICE / HINT

NOTICE:
Handling urea solution
·

Wear protective equipment as necessary (protective glasses and gloves).

·

Do not dilute urea solution.

·

If urea solution contacts your eyes or skin, immediately wash the contacted area with a large amount of water and consult a doctor as necessary.

·

If urea solution dries, it deposits a white powder. Also, if urea solution contacts metals such as copper and aluminum for a long period of time, it may promote corrosion. Therefore, if urea solution is spilled, dampen a cloth or other item and wipe it up or rinse the area with cool or warm water.


Handling the urea injector assembly
·

The urea injector assembly is a precision instrument. Take necessary precautions for installation and shipping. Do not use the part if it has been struck or dropped.

·

If the urea solution remaining inside the urea injector assembly dries out, it may become unable to inject urea solution. Therefore, conduct urea tube with heater assembly installation and removal quickly.

·

If the urea solution dries out and deposition occurs, urea may cling to the O-ring of the pipe and cause seal problems. Therefore, clean the urea tube with heater assembly and intake port of the urea injector assembly with water before attaching them.

·

Perform this procedure in an environment where urea solution will not freeze.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT UREA SOLUTION PIPE
a.

Check the urea injector assembly and the area between the urea injector assembly and urea pump for urea solution leaks.

HINT:

If the urea solution dries on an object, deposition occurs and leaves behind a white powder.



b.

Check that the pipe from the urea injector assembly to the urea pump is free of twisting, bending and blockage.


OK:

Urea solution pipe is normal.


Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR CONNECTION CONDITION (UREA PUMP)

NG

16.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
2.CHECK CONNECTOR CONNECTION CONDITION (UREA PUMP)
a.

Check the connector connection and contact pressure of the urea pump connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR CONNECTION CONDITION (DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

15.CONNECT SECURELY
3.CHECK CONNECTOR CONNECTION CONDITION (DCU (EMISSION CONTROL ECU ASSEMBLY))
a.

Check the connector connection and contact pressure of the DCU (emission control ECU assembly) connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

4.CHECK FOR UREA SOLUTION LEAKS

NG

13.CONNECT SECURELY
4.CHECK FOR UREA SOLUTION LEAKS
a.

Remove the urea injector assembly from the front exhaust pipe assembly.

HINT:
·

Do not disconnect the urea injector assembly from the urea tube with heater assembly.

·

Use a cover, etc., to prevent foreign matter from entering the exhaust pipe.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Pressure Rising Diagnosis (Leak Test).


f.

Perform the Utility and check that there are no urea solution leaks in the urea injector assembly and the area from the urea injector assembly to the urea pump.


OK:

No urea solution leaks in urea injector assembly and area from urea injector assembly to urea pump.


g.

Repair any trouble areas.


Result:
Proceed to
NEXT



NEXT

5.INSPECT UREA PUMP
5.INSPECT UREA PUMP
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Pressure Rising Diagnosis (Leak Test).


e.

Perform the Utility and check that "Pressure Rising Diagnosis (Leak Test)" completes normally.

OK:

"Pressure Rising Diagnosis (Leak Test)" completes normally.



HINT:

If an error message is displayed other than the messages below, perform the corrective action according to the error message, and then retry the test.

·

Reductant Pressure is high.

·

Do not hold Reductant Pump Pressure.

·

Reductant Pump Start Test has failed.

·

Reductant Pump activate has failed.



Result:
Proceed to
OK
NG



OK

6.INSPECT UREA PUMP

NG

11.REPLACE UREA PUMP
6.INSPECT UREA PUMP
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Pressure Rising Diagnosis (Leak Test).


e.

During the Utility, check the pump motor speed.

OK:

2700 rpm or more.



Result:
Proceed to
OK
NG



OK

7.END

NG

8.REPLACE UREA PUMP
7.END
a.

Clean the inside of the urea tank with fresh water or dilute urea solution.


Result:
Proceed to
NEXT



NEXT

17.CLEAR DTC
8.REPLACE UREA PUMP

NOTICE:

Clean the urea tank with fresh water or dilute urea solution.


Result:
Proceed to
NEXT



NEXT

9.INSPECT DCU (EMISSION CONTROL ECU ASSEMBLY)
9.INSPECT DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Pressure Rising Diagnosis (Leak Test).


e.

Perform the Utility and check that "Pressure Rising Diagnosis (Leak Test)" completes normally.

OK:

"Pressure Rising Diagnosis (Leak Test)" completes normally with "Reductant Pump Pressure" from 4.5 to 5.5 bar.


HINT:

If an error message is displayed other than the messages below, perform the corrective action according to the error message, and then retry the test.

·

Reductant Pressure is high.

·

Do not hold Reductant Pump Pressure.

·

Reductant Pump Start Test has failed.

·

Reductant Pump activate has failed.




Result:
Proceed to
OK
NG



OK

10.CHECK FOR UREA SOLUTION LEAKS

NG

14.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
10.CHECK FOR UREA SOLUTION LEAKS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Pressure Rising Diagnosis (Leak Test).


e.

Perform the Utility and check that there are no urea solution leaks in the area from the urea injector assembly to the urea pump.


OK:

No urea solution leaks.


Result:
Proceed to
OK
NG



OK

17.CLEAR DTC

NG

12.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
11.REPLACE UREA PUMP

NOTICE:

Clean the urea tank with fresh water or dilute urea solution.


Result:
Proceed to
NEXT



NEXT

17.CLEAR DTC
12.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
a.

Repair or replace the malfunctioning parts, component and area.


Result:
Proceed to
NEXT



NEXT

17.CLEAR DTC
13.CONNECT SECURELY
a.

Securely connect the DCU (emission control ECU assembly) connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

17.CLEAR DTC
14.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

17.CLEAR DTC
15.CONNECT SECURELY
a.

Securely connect the urea pump connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

17.CLEAR DTC
16.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
a.

Repair or replace the malfunctioning parts, component and area.

NOTICE:

After repairs, clean the inside with fresh water or dilute urea solution.



Result:
Proceed to
NEXT



NEXT

17.CLEAR DTC
17.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

18.CHECK WHETHER DTC OUTPUT RECURS (DTC P20E865)
18.CHECK WHETHER DTC OUTPUT RECURS (DTC P20E865)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END