Urea solution line pressure depends on flow rate of the urea pump.
Urea pump flow rate is determined by value of the pressure sensor which is built in the urea pump.
| *1 | Muffler | *2 | Urea Injector Assembly |
| *3 | Urea Tube with Heater Assembly | *4 | Urea Pump |
| *5 | Pressure Sensor | *6 | Pump Motor |
| *7 | Temperature Sensor | *8 | Level Sensor |
| *9 | Urea Sensor Assembly | *10 | Urea Solution Quality Sensor |
| *11 | Urea Tank | - | - |
| *a | Harness Connector | *b | Pressure Line |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | Memory |
|---|---|---|---|---|---|---|
| P20E985 | Reductant Pressure Too High Signal Above Allowable Range | Diagnosis Condition:
·
SCR inlet exhaust gas temperature is higher than 160°C (320°F). ·
Urea solution defrosting is done. Malfunction Status: ·
During pressure rising mode or pressure keep mode, the abnormal high pressure is detected with the urea solution pressure. Malfunction Duration: ·
- |
·
Urea pump ·
Urea tube with heater assembly ·
Urea injector assembly ·
DCU (emission control ECU assembly) |
Class A | AdBlue consumption warning light:
Comes on |
DTC stored |
Abnormal pressure in the urea solution pipe is detected.
After having restored to the normal conditions.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P20E985 | Perform the "Pressure Rising Diagnosis (Leak Test)" Utility to increase the pressure to 5 bar, and then wait for 2 minutes or more. |
Wear protective equipment as necessary (protective glasses and gloves).
Do not dilute urea solution.
If urea solution contacts your eyes or skin, immediately wash the contacted area with a large amount of water and consult a doctor as necessary.
If urea solution dries, it deposits a white powder. Also, if urea solution contacts metals such as copper and aluminum for a long period of time, it may promote corrosion. Therefore, if urea solution is spilled, dampen a cloth or other item and wipe it up or rinse the area with cool or warm water.
The urea injector assembly is a precision instrument. Take necessary precautions for installation and shipping. Do not use the part if it has been struck or dropped.
If the urea solution remaining inside the urea injector assembly dries out, it may become unable to inject urea solution. Therefore, conduct urea tube with heater assembly installation and removal quickly.
If the urea solution dries out and deposition occurs, urea may cling to the O-ring of the pipe and cause seal problems. Therefore, clean the urea tube with heater assembly and intake port of the urea injector assembly with water before attaching them.
Perform this procedure in an environment where urea solution will not freeze.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Remove the urea injector assembly from the front exhaust pipe assembly.
Do not disconnect the urea injector assembly from the urea tube with heater assembly.
Use a cover, etc., to prevent foreign matter from entering the exhaust pipe.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Pressure Rising Diagnosis (Leak Test).
Perform the Utility and check that there are no urea solution leaks in the urea injector assembly and the area from the urea injector assembly to the urea pump.
No urea solution leaks in urea injector assembly and area from urea injector assembly to urea pump.
Repair any trouble areas.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Pressure Rising Diagnosis (Leak Test).
Perform the Utility and check the Reductant Pump Pressure.
If an error message is displayed other than the messages below, perform the corrective action according to the error message, and then retry the test.
Reductant Pressure is high.
Do not hold Reductant Pump Pressure.
Reductant Pump Start Test has failed.
Reductant Pump activate has failed.
| Result | Proceed to |
|---|---|
| Reductant Pump Pressure is 4.5 to 5.5 bar | A |
| Except above | B |
A
B
Replace the urea pump.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Pressure Rising Diagnosis (Leak Test).
Perform the Utility and check the Reductant Pump Pressure.
"Pressure Rising Diagnosis (Leak Test)" completes normally with "Reductant Pump Pressure" from 4.5 to 5.5 bar.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Pressure Rising Diagnosis (Leak Test).
Perform the Utility and check that there are no urea solution leaks in the area from the urea injector assembly to the urea pump.
No urea solution leaks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair the urea solution leaks.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the DCU (emission control ECU assembly).
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.
Read the DTCs.
DTCs are not output
| Proceed to |
|---|
| NEXT |
NEXT