Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  U02A231  Lost Communication with Reductant Quality Module No Signal  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
U02A231 Lost Communication with Reductant Quality Module No Signal Diagnosis Condition:
·

Ignition switch ON.

·

Battery voltage is 9 V or higher and 16 V or less.


Malfunction Status:
·

CAN data from urea solution quality sensor (urea sensor assembly) is not received.


Malfunction Duration:
·

35 seconds or more.


·

Harness or connector

·

Urea solution quality sensor (urea sensor assembly)

·

DCU (emission control ECU assembly)

·

CAN communication system


Class B1 AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

CAN communication with urea solution quality sensor (urea sensor assembly) is interrupted.


Reset condition

After normal operation is restored and the ignition switch is turned off.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
U02A231 Ignition switch ON for 35 seconds or more.

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

According to the display on the GTS, select "Health Check".


e.

Check for currently output system DTCs.

Result:
Result Proceed to
DTC U02A231 is output A
2 or more of the following DTCs are simultaneously output: U010031, U02A231 and engine DTCs U010A, U010C, U010E, U029D, U029E, U02A2 and U02A3 B
DTCs are not output C




A

2.CHECK HARNESS AND CONNECTOR (UREA SOLUTION QUALITY SENSOR (UREA SENSOR ASSEMBLY) POWER SOURCE VOLTAGE)

B

C

2.CHECK HARNESS AND CONNECTOR (UREA SOLUTION QUALITY SENSOR (UREA SENSOR ASSEMBLY) POWER SOURCE VOLTAGE)
a.
A444338C01
0.229,0.885 0.635,1.219 0.406,0.333 1.802,1.833 2.01,0.938 true 2.365,1.833 2.125,1.229 true 0.156,0.125 0.469,0.281 0.313,0.156 10 false *a 0.323,0.979 0.635,1.177 0.313,0.198 10 false P13 1.656,1.854 1.969,2.052 0.313,0.198 10 false VCC 2.271,1.844 2.583,2.042 0.313,0.198 10 false GND
*a Front view of wire harness connector
(to Urea Solution Quality Sensor (Urea Sensor Assembly))


Disconnect the urea solution quality sensor (urea sensor assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
P13-3 (VCC) - P13-6 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

NG

9.CHECK HARNESS AND CONNECTOR (UREA SOLUTION QUALITY SENSOR (UREA SENSOR ASSEMBLY) - BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Disconnect the cable from the negative (-) battery terminal.


b.

Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-11 (CA2H) - E-10 (CA2L) Ignition switch off 54 to 69 Ω
Positive (+) battery terminal - E-11 (CA2H) Ignition switch off 6 kΩ or higher
Positive (+) battery terminal - E-10 (CA2L)
E-11 (CA2H) - Body ground Ignition switch off 200 Ω or higher
E-10 (CA2L) - Body ground



Result:
Proceed to
OK
NG



OK

4.REPLACE UREA SOLUTION QUALITY SENSOR (UREA SENSOR ASSEMBLY)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE UREA SOLUTION QUALITY SENSOR (UREA SENSOR ASSEMBLY)
a.

Replace the urea solution quality sensor (urea sensor assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC U02A231)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC U02A231)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC U02A231 is output A
DTCs are not output B




A

7.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

B

END

7.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
9.CHECK HARNESS AND CONNECTOR (UREA SOLUTION QUALITY SENSOR (UREA SENSOR ASSEMBLY) - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P13-6 (GND) - Body ground Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.REPAIR OR REPLACE HARNESS OR CONNECTOR (ABS MTR/DCU RELAY - UREA SOLUTION QUALITY SENSOR (UREA SENSOR ASSEMBLY))

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPAIR OR REPLACE HARNESS OR CONNECTOR (ABS MTR/DCU RELAY - UREA SOLUTION QUALITY SENSOR (UREA SENSOR ASSEMBLY))
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
12.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC U02A231)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC U02A231)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END