Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) › from 2019.08
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C1232  Acceleration Sensor Stuck Malfunction  C1243  Acceleration Sensor Stuck Malfunction  C1245  Acceleration Sensor Output Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag ECU assembly) via CAN communication.

The acceleration sensor inside the yaw rate and acceleration sensor detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is a malfunction in the bus lines between the yaw rate and acceleration sensor (airbag ECU assembly) and the CAN communication system, DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output. When DTC U0124 is output together with C1232, C1243 and/or C1245, inspect and repair the trouble areas indicated by U0124 first.

These DTCs are also output when calibration has not been completed.

DTC No. DTC Detection Condition Trouble Area
C1232 At a vehicle speed of 10 km/h (6 mph) or more, either GL1 or GL2 (input signal) does not change for 30 seconds or more.
·

Sensor installation

·

Acceleration sensor (Airbag ECU assembly)


C1243 Either of the following is detected:
·

Output values of GL1 and GL2 do not change 16 times or more while vehicle speed decreases from 30 km/h (19 mph) to 0 km/h (0 mph).

·

Output values of GL1 and GL2 (front and rear, left and right) are outside permitted output range for 60 seconds or more.

·

Left and right output values of GL1 and GL2 are outside permitted output range for 60 seconds or more.


·

Sensor installation

·

Acceleration sensor (Airbag ECU assembly)


C1245 At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
·

Sensor installation

·

Acceleration sensor (Airbag ECU assembly)



WIRING DIAGRAM

C275041E56
6.042,0.698 6.552,0.885 0.51,0.188 10 false CANL 0.813,0.708 1.323,0.896 0.51,0.188 10 false CANL 0.792,1.333 1.302,1.521 0.51,0.188 10 false CANH 6.042,1.323 6.552,1.51 0.51,0.188 10 false CANH 0.948,1.938 1.344,2.135 0.396,0.198 10 false IG2 1.313,0.542 1.615,0.74 0.302,0.198 10 false 22 0.99,3.177 1.323,3.375 0.333,0.198 10 false E2 0.99,2.563 1.385,2.76 0.396,0.198 10 false E1 1.302,1.156 1.604,1.354 0.302,0.198 10 false 13 1.313,1.833 1.615,2.031 0.302,0.198 10 false 21 1.313,2.438 1.615,2.635 0.302,0.198 10 false 25 1.313,3.052 1.615,3.25 0.302,0.198 10 false 26 5.771,1.167 6.167,1.365 0.396,0.198 10 false 22 5.771,0.563 6.104,0.76 0.333,0.198 10 false 10 3.927,1.948 5,2.135 1.073,0.188 10 false from IG circuit 2.042,2.094 2.927,2.281 0.885,0.188 10 false A/BAG-IG2 3.708,3.406 5.552,3.625 1.844,0.219 10 false : CAN Communication Line 0.323,3.927 0.688,4.115 0.365,0.188 10 false A58 5.552,3.896 5.917,4.083 0.365,0.188 10 false A71 0.333,4.125 2.5,4.51 2.167,0.385 10 false Yaw Rate and Acceleration Sensor (Airbag ECU Assembly) 5.5,4.083 7.094,4.438 1.594,0.354 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the yaw rate and acceleration sensor (airbag ECU assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).


HINT:

When U0124 and/or U0126 is output together with C1232, C1243 and/or C1245, inspect and repair the trouble areas indicated by U0124 and/or U0126 first (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>U0073).


PROCEDURE

1.CHECK DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

At a speed of 30 km/h (19 mph) or more, drive the vehicle, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.


e.

Check that no CAN communication system DTC is output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


f.

Check if DTCs for zero point calibration of the yaw rate sensor undone (C1210) or for zero point calibration of the acceleration sensor undone (C1336) are output (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).


Result:
Result Proceed to
DTC (relating to yaw rate and acceleration sensor) is output A
DTC (relating to CAN communication system) is output B
DTC (C1210 and/or C1336) are output C



A

2.CHECK AIRBAG ECU ASSEMBLY INSTALLATION

B

C

2.CHECK AIRBAG ECU ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and acceleration sensor (airbag ECU assembly) has been installed properly (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG ECU>INSTALLATION).

OK:

The sensor should be tightened to the specified torque.

The sensor should not be tilted position.


NOTICE:

Check the yaw rate and acceleration sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).



Result:
Proceed to
OK
NG



OK

NG

INSTALL AIRBAG ECU ASSEMBLY CORRECTLY