Home › Engine / Hybrid System › N04C-WA (CHARGING) › GENERATOR › from 2019.08
RM2850E _51 Engine / Hybrid System _082620 N04C-WA CHARGING _0402275 GENERATOR A

N04C-WA CHARGING  GENERATOR  INSTALLATION  


PROCEDURE

Hide 27020 1.INSTALL GENERATOR ASSEMBLY

a.
A398667E03
1.958,0.313 1.729,0.646 true 1.896,0.146 2.083,0.333 0.188,0.188 10 true *1 0.677,1.74 0.896,1.917 0.219,0.177 10 false *a 0.667,0.531 0.885,0.708 0.219,0.177 10 false *b 2.125,1.177 2.344,1.354 0.219,0.177 10 false *c 2.406,0.521 2.594,0.688 0.188,0.167 10 true *c

Temporarily install the generator assembly with the bolt A.


b.

Temporarily install the generator bracket with the bolt B to the generator assembly.


c.

Install the generator bracket with the 2 bolts C.

Torque:

97 N*m (989 kgf*cm, 72 ft.*lbf)



d.

Tighten the bolt A and bolt B.

Torque:

55 N*m (561 kgf*cm, 41 ft.*lbf)


Text in Illustration
*1 Generator Bracket
*a Bolt A
*b Bolt B
*c Bolt C


e.
A398666E03
1.677,1.906 1.896,2.094 0.219,0.188 10 true *a 0.479,1.094 0.698,1.281 0.219,0.188 10 true *b 1.24,1.125 1.417,1.313 0.177,0.188 10 true *c 1.271,0.385 1.448,0.573 0.177,0.188 10 true *c

Install the nut to connect the terminal B.

Torque:

9.8 N*m (100 kgf*cm, 87 in.*lbf)



f.

Connect the connector.


g.

Install the wire harnesses with the 2 bolts to the generator bracket.

Torque:

8.4 N*m (86 kgf*cm, 74 in.*lbf)


Text in Illustration
*a Nut
*b Connector
*c Bolt


h.
A398665E01
0.375,1.583 0.531,1.76 0.156,0.177 10 true *a 0.698,0.219 0.854,0.396 0.156,0.177 10 true *b 1.135,1.146 1.292,1.323 0.156,0.177 10 true *b 1.479,1.323 1.635,1.5 0.156,0.177 10 true *b 2.781,1.188 2.938,1.365 0.156,0.177 10 true *b

Install the terminal cap.


i.

Attach the clamps.

*a Terminal Cap
*b Clamp


Hide 16361A 5.INSTALL FAN AND GENERATOR V BELT

Hide 88310A 6.INSTALL NO. 1 V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT

Hide 58701A 8.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY

Hide 33820B 9.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 58841A 10.INSTALL SHIFTING HOLE COVER (for Automatic Transmission)

Hide 58123A 11.INSTALL SHIFT AND SELECT LEVER SUPPORT WITH BOOTS (for Manual Transmission)

Hide 58420 12.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 58734B 13.INSTALL REAR ENGINE SERVICE COVER WEATHERSTRIP

Hide 58410 14.INSTALL ENGINE SERVICE HOLE COVER

Hide 58521D 15.INSTALL ENGINE SERVICE HOLE COVER MAT

Hide 16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION