23849G
1.INSTALL FUEL PIPE SUPPORT
Install the fuel pipe support with the 2 bolts.
23809L
2.INSTALL FUEL PIPE SUPPORT SUB-ASSEMBLY
Install the fuel pipe support sub-assembly with the 2 bolts.
17111
3.INSTALL INTAKE MANIFOLD
17141
4.INSTALL EXHAUST MANIFOLD
17107
5.INSTALL EXHAUST MANIFOLD HEAT INSULATOR SUB-ASSEMBLY
16206A
6.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Install 3 new O-rings and install the No. 2 water by-pass pipe sub-assembly with the 5 bolts.
12204
7.INSTALL VENTILATION VALVE SUB-ASSEMBLY
Install the ventilation valve sub-assembly with the bolt.
Connect the hose and slide the clamp to secure the hose.
8.INSTALL OIL COOLER COVER SUB-ASSEMBLY
23264D
9.INSTALL FUEL FILTER BRACKET
Install the fuel filter bracket with the 2 bolts.
23849G
10.INSTALL FUEL PIPE SUPPORT
Install the fuel pipe support with the bolt.
29300
11.INSTALL VACUUM PUMP ASSEMBLY
Install a new O-ring and the vacuum pump assembly with the 2 nuts.
29601B
12.INSTALL VACUUM PUMP OIL PIPE SUB-ASSEMBLY
Install 3 new gaskets and the vacuum pump oil pipe sub-assembly with the 3 union bolts.
19971E
13.INSTALL VACUUM PIPE
Install 2 new gaskets and the vacuum pipe with the union bolt.
Install the pipe clamp with the nut. Tighten the nut until the clamp edges make contact.
23310
14.INSTALL UPPER FUEL FILTER BODY
Install the upper fuel filter body with the 2 bolts.
23803H
15.INSTALL FUEL RETURN PIPE SUB-ASSEMBLY
Install 2 new gaskets and the fuel return pipe sub-assembly with union bolt.
89458G
16.INSTALL NO. 2 FUEL PRESSURE SENSOR
23300D
17.INSTALL DIESEL FUEL FILTER ASSEMBLY
18.INSTALL NO. 3 NOZZLE LEAKAGE PIPE SUB-ASSEMBLY
Install new 2 gaskets and the No. 3 nozzle leakage pipe sub-assembly with the 2 union bolts.
Install the fuel pipe clamp with the nut.
Tighten the nut until the clamp edges make contact with the engine side clamp edges.
22100
19.INSTALL FUEL SUPPLY PUMP ASSEMBLY
22214B
20.INSTALL FUEL ADDITION CUT VALVE ASSEMBLY
23810A
21.INSTALL COMMON RAIL ASSEMBLY
16100
22.INSTALL ENGINE WATER PUMP ASSEMBLY
16206
23.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
Install 3 new O-rings, 2 new gaskets and the water by-pass pipe sub-assembly with the 8 bolts.
24.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY
Connect the water hose and slide the clamp to secure the hose.
Install the No. 3 water by-pass pipe sub-assembly with the 2 bolts.
Connect the connector.
87208L
25.INSTALL WATER PIPE SUB-ASSEMBLY
Install a new O-ring and the water pipe sub-assembly with the 3 bolts.
16333
26.INSTALL WATER OUTLET HOUSING
Install a new gasket and the water outlet housing with the 3 bolts.
16331A
27.INSTALL THERMOSTAT
88431A
28.INSTALL NO. 2 COMPRESSOR MOUNTING BRACKET
Temporarily install to the No. 1 compressor mounting bracket and No. 2 compressor mounting bracket with the 7 bolts.
|
for bolt A |
|
for bolt B |
Tighten the 7 bolts.
Firmly press and hold, the No. 1 compressor mounting bracket and No. 2 compressor mounting bracket against the timing gear cover to eliminate any gaps. Then uniformly tighten the 7 bolts.
88440B
29.INSTALL IDLE PULLEY ASSEMBLY WITH BRACKET
Install the idle pulley assembly with bracket with the 3 bolts.
16630G
30.INSTALL IDLER PULLEY ASSEMBLY
Install the idler pulley assembly with the 2 bolts.
11301K
31.INSTALL CRANKSHAFT POSITION SENSOR
11301M
32.INSTALL CAMSHAFT POSITION SENSOR
83420
33.INSTALL WATER TEMPERATURE SENDER GAUGE ASSEMBLY
17201
34.INSTALL TURBOCHARGER SUB-ASSEMBLY
44310
35.INSTALL VANE PUMP ASSEMBLY
Coat a new O-ring with power steering fluid and install it onto the vane pump assembly.
Install the vane pump assembly with the 2 bolts.
23670
36.INSTALL INJECTOR ASSEMBLY
37.INSTALL INJECTION PIPE SUB-ASSEMBLY
23741B
38.INSTALL INJECTION PIPE CLAMP
16577C
39.INSTALL RADIATOR PIPE
Install a new gasket and the radiator pipe with the 2 bolts.
26100
40.INSTALL DIESEL THROTTLE BODY
25620
41.INSTALL EGR VALVE ASSEMBLY
11202D
42.INSTALL NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY
Install 4 new No. 2 cylinder head cover gaskets to the 4 injector assemblies.
| *a | Connector Insertion Side of Injector Assembly |
|
Engine Oil |
To make inserting the part into the injector assembly easier, align the part with the head shape of the injector assembly.
The No. 2 cylinder head cover sub-assembly can be installed in any direction.
Apply a light coat of the engine oil to the 4 No. 2 cylinder head cover gaskets as shown in the illustration.
Install a new cylinder head cover gasket to the No. 2 cylinder head cover sub-assembly.
Install the 2 cylinder head cover spacers and 2 cylinder head cushion to the No. 2 cylinder head cover sub-assembly.
Install the No. 2 cylinder head cover sub-assembly with the 2 bolts.
Connect the PCV hose and install the oil separator assembly with the 6 bolts.
Connect the 4 connectors and install the wire harness with the bolt.
12601B
43.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
Install the No. 1 engine cover sub-assembly with the 2 bolts.
12180E
44.INSTALL OIL FILLER CAP ASSEMBLY
Install the oil filler cap sub-assembly.
45.REMOVE ENGINE STAND
Install the No. 1 engine hanger with the 2 bolts.
Install the generator bracket with the 2 bolts.
Attach an engine sling device and hang the engine assembly with a chain block.
Lift the engine assembly and remove it from the engine stand.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
11000
46.INSTALL ENGINE ASSEMBLY
Using an engine lifter, support the engine and height adjustments or plate lift attachments.
Place the height adjustments and plate lift attachments so that the engine assembly is level.
Securely support the engine assembly to prevent it from turning upside down until it is secured to the engine lifter.
Install the engine assembly.
Install the front No. 1 engine mounting bracket LH with the 4 bolts.
Install the engine mounting stabilizer and front engine mounting insulator with the 2 nuts and washer.
Install the front No. 1 engine mounting bracket RH with the 4 bolts.
Install the engine mounting stabilizer and front engine mounting insulator with the 2 nuts and washer.
87207J
47.CONNECT NO. 1 WATER PIPE AND HOSE SUB-ASSEMBLY
| *A | for Manual Transmission |
| *B | for Automatic Transmission |
|
Bolt A |
|
Bolt B |
Connect the No. 1 water pipe and hose sub-assembly with the 6 bolts.
23271F
48.CONNECT FUEL HOSE
Connect the 2 fuel hoses and slide the 2 clamps to secure the hoses.
44774
49.CONNECT UNION TO CONNECTOR TUBE HOSE
Connect the union to connector tube hose and slide the clamp to secure the hose.
88320
50.CONNECT COOLER COMPRESSOR ASSEMBLY
Connect the cooler compressor assembly with the 4 bolts.
Connect the connector.
87245B
51.CONNECT INLET HEATER WATER HOSE B
Connect the inlet heater water hose B and slide the clamp to secure the hose.
87246B
52.CONNECT OUTLET HEATER WATER HOSE B
Connect the outlet heater water hose B and slide the clamp to secure the hose.
82121
53.CONNECT ENGINE WIRE
| *a | LH Side |
| *b | RH Side |
|
Bolt |
|
Nut |
Connect the engine wire to the engine assembly with the 2 bolts and nut.
Connect the engine wire to the No. 1 engine hanger with the 2 bolts.
31250
54.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)
31210
55.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)
31210
56.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)
35000
57.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
33110
58.INSTALL MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
51202D
59.CONNECT FRONT LOWER SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Install the front lower suspension crossmember sub-assembly with the 6 bolts, 4 washers and 4 nuts.
45450
60.CONNECT STEERING RELAY ROD ASSEMBLY
| *a | for Center Arm Bracket Assembly Side |
| *b | for Idler Arm Bracket Assembly Side |
Connect the steering relay rod assembly to the center arm bracket assembly and idler arm bracket assembly with the 2 nuts.
Install 2 new cotter pins.
Connect the steering relay rod assembly to the tie rod assembly LH with the nut.
Install a new cotter pin.
37140
61.INSTALL FRONT PROPELLER SHAFT ASSEMBLY
27020
62.INSTALL GENERATOR ASSEMBLY
44411
63.CONNECT PRESSURE FEED HOSE
Install a new gasket and connect the pressure feed hose to the vane pump assembly with the union bolt.
44348A
64.CONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE
Connect the No. 1 oil reservoir to pump hose to the vane pump assembly, and slide the clamp to secure the hose.
28100
65.INSTALL STARTER ASSEMBLY
25608
66.INSTALL EGR COOLER SUB-ASSEMBLY
46700
67.INSTALL EXHAUST RETARDER ASSEMBLY
17410
68.INSTALL FRONT EXHAUST PIPE ASSEMBLY
16400
69.INSTALL RADIATOR ASSEMBLY
58701A
70.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY
Install the front engine service cover panel sub-assembly with the 5 bolts.
for Automatic Transmission:
Connect the 2 connectors to the transmission floor shift assembly.
33820B
71.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
for Automatic Transmission:
Connect the transmission control cable assembly to the front engine service cover panel sub-assembly.
Install a new clip.
Install the clamp with the bolt.
Connect the transmission control cable assembly to the transmission floor shift assembly with the plate washer and new clip.
for Manual Transmission:
Connect the transmission control cable assembly and plate washer with the nut and 3 new clips.
58841A
72.INSTALL SHIFTING HOLE COVER (for Automatic Transmission)
58123A
73.INSTALL SHIFT AND SELECT LEVER SUPPORT WITH BOOTS (for Manual Transmission)
Install the shift and select lever support with boots with the 4 bolts.
Install the transmission cover mat.
Install the shift lever knob sub-assembly.
74.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
75.CHECK INJECTOR COMPENSATION CODE
76.ADD ENGINE OIL
77.ADD ENGINE COOLANT
78.ADD POWER STEERING FLUID
79.ADD AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)
80.ADD MANUAL TRANSMISSION OIL (for Manual Transmission)
81.BLEED AIR FROM FUEL SYSTEM
82.INSPECT FOR ENGINE SPEED
83.INSPECT FOR FUEL LEAK
84.INSPECT FOR COOLANT LEAK
85.INSPECT FOR OIL LEAK
86.BLEED AIR FROM POWER STEERING SYSTEM
87.INSPECT FOR POWER STEERING FLUID LEAK
88.INSPECT FOR EXHAUST GAS LEAK
89.INSPECT FOR DRIVE BELT
53711C
90.INSTALL FRONT FENDER APRON RH
Install the front fender apron RH with the 7 bolts.
53712C
91.INSTALL FRONT FENDER APRON LH
Install the front fender apron LH with the 6 bolts.
51445D
92.INSTALL ENGINE UNDER COVER BRACKET RH
Install the engine under cover bracket RH with the 2 bolts.
51446C
93.INSTALL ENGINE UNDER COVER BRACKET LH
Install the engine under cover bracket LH with the 2 bolts.
51441D
94.INSTALL NO. 1 ENGINE UNDER COVER
58420
95.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY
| *a | Knob |
Attach the 2 guides and install the No. 2 engine service hole cover assembly, Turn the knob to attach the hook.
58734B
96.INSTALL REAR ENGINE SERVICE COVER WEATHERSTRIP
Install the rear engine service cover weatherstrip.
58410
97.INSTALL ENGINE SERVICE HOLE COVER
Attach the 2 guides, 2 hooks and install the engine service hole cover.
58521D
98.INSTALL ENGINE SERVICE HOLE COVER MAT
Install the engine service hole cover mat.