Prolonged and repeated contact with engine oil will cause the loss of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants that may cause skin cancer.
Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use a waterless hand cleaner to remove any used engine oil. Do not use gasoline, thinners or solvents.
For environmental protection, used oil and used oil filters must be disposed of at designated disposal sites.
1.REMOVE ENGINE SERVICE HOLE MAIN COVER
58734B
2.REMOVE REAR ENGINE SERVICE COVER WEATHERSTRIP
3.DRAIN ENGINE OIL
Remove the oil filler cap sub-assembly.
Remove the drain plug and gasket from the oil pan and drain the engine oil into a container.
Clean the drain plug.
Install the drain plug with a new gasket.
15613
4.REMOVE OIL FILTER ELEMENT
| *a | Drain Adapter |
| *b | Pipe |
| *c | Hose |
Connect a hose with an inner diameter of 12 mm (0.472 in.) to the pipe.
Firmly insert the hose until it contacts the base of the drain adapter pipe.
Remove the oil filter plug and O-ring (for plug) from the oil filter cap assembly.
After removing the oil filter plug, a small amount of oil may drip out, so wipe it with a cloth.
| *1 | Oil Filter Cap Assembly |
| *a | Drain Adapter |
| *b | Pipe |
Install the drain adapter and its installed hose to the oil filter cap assembly, and then tighten it until the drain adapter contacts the surface. After making contact, tighten the drain adapter until it can no longer be turned by hand.
Do not install and tighten the drain adapter using tools such as pliers. Otherwise, the drain adapter may be damaged.
Use a container to catch the draining engine oil.
Check that the engine oil has been drained and remove the drain adapter.
Remove the oil filter cap assembly.
| *1 | Oil Filter Element |
| *2 | O-Ring (for cap) |
Remove the oil filter element and O-ring (for cap) from the oil filter cap assembly.
To prevent damage to the O-ring groove, remove the O-ring (for cap) by hand and do not use any tools.
15613
5.INSTALL OIL FILTER ELEMENT
Clean the inside of the oil filter cap assembly, the threads and O-ring groove.
| *1 | O-Ring (for cap) |
| *a | CORRECT |
| *b | INCORRECT |
Apply a light coat of engine oil to a new O-ring (for cap), and install it to the oil filter cap assembly.
Be sure to install the O-ring in the proper position, otherwise engine oil may leak.
Do not twist the O-ring.
Attach a new O-ring after brakes cleaner volatilized enough when use brakes cleaner to prevent the deterioration of the O-ring.
Set a new oil filter element to the oil filter cap assembly.
Remove any dirt or foreign matter from the installation surface and inside of the engine.
Again apply a light coat of engine oil to the O-ring (for cap), and install the oil filter cap assembly.
Make sure that the O-ring (for cap) is not pinched.
| *1 | Oil Filter Cap Assembly |
| *2 | O-Ring (for cap) |
| *3 | Oil Cooler Cover Sub-assembly |
| *a | No Gap |
Tighten the oil filter cap assembly.
After tightening the oil filter cap assembly, check for gaps between the installation surfaces and protrusion of O-ring (for cap).
| *1 | O-Ring (for plug) |
Apply a light coat of engine oil to a new O-ring (for plug), and install it to the oil filter cap assembly.
Remove any dirt or foreign matter from the installation surface.
Install the oil filter plug to the oil filter cap assembly.
Make sure that the O-ring (for plug) is not pinched.
6.ADD ENGINE OIL
Add fresh oil and install the oil filler cap sub-assembly.
| Oil Grade | |
|---|---|
| API CH-4, CI-4 or CI-4 PLUS, ACEA E-4, E-7
JASO DH-1 |
·
5W-30 ·
10W-30 ·
15W-40 |
| Item | Fill amount |
|---|---|
| Drain and refill with oil filter change | 7.7 liters (8.1 US qts, 6.8 Imp. qts) |
| Drain and refill without oil filter change | 6.3 liters (6.7 US qts, 5.5 Imp. qts) |
| Dry fill | 8.4 liters (8.9 US qts, 7.4 Imp. qts) |
7.INSPECT FOR OIL LEAK
Warm up the engine and check for engine oil leaks.
8.INSPECT ENGINE OIL LEVEL
58734B
9.INSTALL REAR ENGINE SERVICE COVER WEATHERSTRIP
10.INSTALL ENGINE SERVICE HOLE MAIN COVER