Home › Engine / Hybrid System › N04C-VQ (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2019.08
RM2850E _51 Engine / Hybrid System _073144 N04C-VQ ENGINE MECHANICAL _0355904 ENGINE ASSEMBLY A

N04C-VQ ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 23849G 1.INSTALL FUEL PIPE SUPPORT

a.

Install the fuel pipe support with the 2 bolts.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide 23809L 2.INSTALL FUEL PIPE SUPPORT SUB-ASSEMBLY

a.

Install the fuel pipe support sub-assembly with the 2 bolts.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide 17107 5.INSTALL EXHAUST MANIFOLD HEAT INSULATOR SUB-ASSEMBLY

Hide 16206A 6.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install 3 new O-rings and install the No. 2 water by-pass pipe sub-assembly with the 5 bolts.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide 12204 7.INSTALL VENTILATION VALVE SUB-ASSEMBLY

a.

Install the ventilation valve sub-assembly with the bolt.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


b.

Connect the hose and slide the clamp to secure the hose.


Hide 8.INSTALL OIL COOLER COVER SUB-ASSEMBLY

Hide 23264D 9.INSTALL FUEL FILTER BRACKET

a.

Install the fuel filter bracket with the 2 bolts.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide 23849G 10.INSTALL FUEL PIPE SUPPORT

a.

Install the fuel pipe support with the bolt.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 29300 11.INSTALL VACUUM PUMP ASSEMBLY

a.

Install a new O-ring and the vacuum pump assembly with the 2 nuts.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide 29601B 12.INSTALL VACUUM PUMP OIL PIPE SUB-ASSEMBLY

a.

Install 3 new gaskets and the vacuum pump oil pipe sub-assembly with the 3 union bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 19971E 13.INSTALL VACUUM PIPE

a.

Install 2 new gaskets and the vacuum pipe with the union bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Install the pipe clamp with the nut. Tighten the nut until the clamp edges make contact.


Hide 23310 14.INSTALL UPPER FUEL FILTER BODY

a.

Install the upper fuel filter body with the 2 bolts.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide 23803H 15.INSTALL FUEL RETURN PIPE SUB-ASSEMBLY

a.

Install 2 new gaskets and the fuel return pipe sub-assembly with union bolt.

Torque:
19.6 N*m (200 kgf*cm, 14 ft.*lbf)


Hide 23802E 16.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY

a.
A258070N04
0.854,0.281 1.021,0.448 0.167,0.167 10 true A 1.396,1.844 1.563,2.01 0.167,0.167 10 true B

Install 3 new gaskets and the No. 4 fuel pipe sub-assembly with the 2 union bolts.

Torque:
for bolt A : 24.5 N*m (250 kgf*cm, 18 ft.*lbf)
for bolt B : 19.6 N*m (200 kgf*cm, 14 ft.*lbf)


Hide 23300D 17.INSTALL DIESEL FUEL FILTER ASSEMBLY

Hide 18.INSTALL NO. 3 NOZZLE LEAKAGE PIPE SUB-ASSEMBLY

Hide 22100 19.INSTALL FUEL SUPPLY PUMP ASSEMBLY

Hide 23810A 20.INSTALL COMMON RAIL ASSEMBLY

Hide 23811 21.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE

Hide 11177 22.INSTALL INJECTION NOZZLE SEAT GASKET

Hide 23670 23.INSTALL INJECTOR ASSEMBLY

Hide 23741B 24.INSTALL INJECTION PIPE CLAMP

Hide 16100 25.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 16206 26.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install 3 new O-rings, 2 new gaskets and the water by-pass pipe sub-assembly with the 8 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 27.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Connect the water hose and slide the clamp to secure the hose.


b.

Install the No. 3 water by-pass pipe sub-assembly with the 2 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


c.

Connect the 2 connectors.


Hide 87208L 28.INSTALL WATER PIPE SUB-ASSEMBLY

a.

Install a new O-ring and the water pipe sub-assembly with the 3 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 16333 29.INSTALL WATER OUTLET HOUSING

a.

Install a new gasket and the water outlet housing with the 3 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 88431A 31.INSTALL NO. 2 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

a.

Temporarily install to the No. 1 compressor mounting bracket and No. 2 compressor mounting bracket with the 7 bolts.


b.
A403298C01
0,0 0,0 false
V100135

for bolt A
V100136

for bolt B


Tighten the 7 bolts.

Torque:
for bolt A : 28.5 N*m (291 kgf*cm, 21 ft.*lbf)
for bolt B : 55 N*m (561 kgf*cm, 41 ft.*lbf)

HINT:

Firmly press and hold, the No. 1 compressor mounting bracket and No. 2 compressor mounting bracket against the timing gear cover to eliminate any gaps. Then uniformly tighten the 7 bolts.



Hide 88440B 32.INSTALL IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)

a.

Install the idle pulley assembly with bracket with the 3 bolts.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide 16630G 33.INSTALL IDLER PULLEY ASSEMBLY

a.

Install the idler pulley assembly with the 2 bolts.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide 83420 36.INSTALL WATER TEMPERATURE SENDER GAUGE ASSEMBLY

Hide 17201 37.INSTALL TURBOCHARGER SUB-ASSEMBLY

Hide 44310 38.INSTALL VANE PUMP ASSEMBLY

a.

Coat a new O-ring with power steering fluid and install it onto the vane pump assembly.


b.

Install the vane pump assembly with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 16577C 39.INSTALL RADIATOR PIPE

a.

Install a new O-ring and the radiator pipe with the 2 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 25620 41.INSTALL EGR VALVE ASSEMBLY

Hide 11202D 42.INSTALL NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Install 4 new No. 2 cylinder head cover gaskets to the 4 injector assemblies.

NOTICE:
·
A451473C01
1.698,0.833 2.177,0.302 2.177,0.302 2.375,0.302 true 2.417,0.198 2.729,0.354 0.313,0.156 10 false *a
*a Connector Insertion Side of Injector Assembly
V100145

Engine Oil


To make inserting the part into the injector assembly easier, align the part with the head shape of the injector assembly.

·

The No. 2 cylinder head cover sub-assembly can be installed in any direction.




b.

Apply a light coat of the engine oil to the 4 No. 2 cylinder head cover gaskets as shown in the illustration.


c.

Install a new cylinder head cover gasket to the No. 2 cylinder head cover sub-assembly.


d.

Install the 2 cylinder head cover spacers and 2 cylinder head cushion to the No. 2 cylinder head cover sub-assembly.


e.

Install the No. 2 cylinder head cover sub-assembly with the 2 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


f.

Connect the PCV hose and install the oil separator assembly with the 6 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.

Connect the 4 connectors and install the wire harness with the bolt.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 12601B 43.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

a.

Install the No. 1 engine cover sub-assembly with the 2 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 12180E 44.INSTALL OIL FILLER CAP ASSEMBLY

a.

Install the oil filler cap sub-assembly.


Hide 45.REMOVE ENGINE STAND

a.

Install the No. 1 engine hanger with the 2 bolts.

Torque:
125 N*m (1275 kgf*cm, 92 ft.*lbf)


b.

Install the generator bracket with the 2 bolts.

Torque:
125 N*m (1275 kgf*cm, 92 ft.*lbf)


c.

Attach an engine sling device and hang the engine assembly with a chain block.


d.

Lift the engine assembly and remove it from the engine stand.

CAUTION:

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.


NOTICE:

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.



Hide 11000 46.INSTALL ENGINE ASSEMBLY

a.

Using an engine lifter, support the engine and height adjustments or plate lift attachments.

NOTICE:
·

Place the height adjustments and plate lift attachments so that the engine assembly is level.

·

Securely support the engine assembly to prevent it from turning upside down until it is secured to the engine lifter.




b.

Install the engine assembly.


c.
A146473E02
1.229,1.24 1.49,1.469 0.26,0.229 10 false A 2.792,1.448 2.979,1.635 0.188,0.188 10 false B

Install the front No. 1 engine mounting bracket LH with the 4 bolts.

Torque:
68.5 N*m (699 kgf*cm, 51 ft.*lbf)


d.

Install the engine mounting stabilizer and front engine mounting insulator with the 2 nuts and washer.

Torque:
for nut A : 87 N*m (887 kgf*cm, 64 ft.*lbf)
for nut B : 90 N*m (918 kgf*cm, 66 ft.*lbf)


e.
A146472E02
1.552,0.573 1.719,0.76 0.167,0.188 10 true A 2.052,2.625 2.219,2.813 0.167,0.188 10 true B

Install the front No. 1 engine mounting bracket RH with the 4 bolts.

Torque:
68.5 N*m (699 kgf*cm, 51 ft.*lbf)


f.

Install the engine mounting stabilizer and front engine mounting insulator with the 2 nuts and washer.

Torque:
for nut A : 87 N*m (887 kgf*cm, 64 ft.*lbf)
for nut B : 90 N*m (918 kgf*cm, 66 ft.*lbf)


Hide 23271F 47.CONNECT FUEL HOSE

a.

Connect the 2 fuel hoses and slide the 2 clamps to secure the hoses.


Hide 44774 48.CONNECT UNION TO CONNECTOR TUBE HOSE

a.

Connect the union to connector tube hose and slide the clamp to secure the hose.


Hide 44379A 49.INSTALL NO. 2 OIL RESERVOIR BRACKET

a.

Install the No. 2 oil reservoir bracket with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 88320 50.CONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

a.

Connect the cooler compressor assembly with the 4 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


b.

Connect the connector.


Hide 87245B 52.CONNECT INLET HEATER WATER HOSE B

a.

Connect the inlet heater water hose B and slide the clamp to secure the hose.


Hide 87246B 53.CONNECT OUTLET HEATER WATER HOSE B

a.

Connect the outlet heater water hose B and slide the clamp to secure the hose.


Hide 82121 54.CONNECT ENGINE WIRE

a.
A399527C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Connect the engine wire to the engine assembly with the 3 bolts and nut.

Torque:
for bolt : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
for nut : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the engine wire to the No. 1 engine hanger with the 2 bolts.

Torque:
17.6 N*m (179 kgf*cm, 13 ft.*lbf)


Hide 31250 55.INSTALL CLUTCH DISC ASSEMBLY

Hide 31210 56.INSTALL CLUTCH COVER ASSEMBLY

Hide 31210 57.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

Hide 51202D 59.CONNECT FRONT LOWER SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Install the front lower suspension crossmember sub-assembly with the 6 bolts, 4 washers and 4 nuts.

Torque:
160 N*m (1632 kgf*cm, 118 ft.*lbf)


Hide 45450 60.CONNECT STEERING RELAY ROD ASSEMBLY

a.
A451477C01
0.135,0.063 0.344,0.25 0.208,0.188 12 false *a 0.135,2.281 0.323,2.458 0.188,0.177 12 false *b 2.833,0.5 2.969,0.667 0.135,0.167 10 false A 0.479,2.896 0.625,3.083 0.146,0.188 10 true B
*a for Center Arm Bracket Assembly Side
*b for Idler Arm Bracket Assembly Side


Connect the steering relay rod assembly to the center arm bracket assembly and idler arm bracket assembly with the 2 nuts.

Torque:
for nut A : 150 N*m (1530 kgf*cm, 111 ft.*lbf)
for nut B : 91 N*m (928 kgf*cm, 67 ft.*lbf)


b.

Install 2 new cotter pins.


c.
A451482

Connect the steering relay rod assembly to the tie rod assembly LH with the nut.

Torque:
155 N*m (1581 kgf*cm, 114 ft.*lbf)


d.

Install a new cotter pin.


Hide 37140 61.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 27020 62.INSTALL GENERATOR ASSEMBLY

Hide 44411 63.CONNECT PRESSURE FEED HOSE

a.

Install a new gasket and connect the pressure feed hose to the vane pump assembly with the union bolt.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 44348A 64.CONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE

a.

Connect the No. 1 oil reservoir to pump hose to the vane pump assembly, and slide the clamp to secure the hose.


Hide 28100 65.INSTALL STARTER ASSEMBLY

Hide 25608 66.INSTALL EGR COOLER SUB-ASSEMBLY

Hide 46700 67.INSTALL EXHAUST RETARDER ASSEMBLY

Hide 17410 68.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 16400 69.INSTALL RADIATOR ASSEMBLY

Hide 58701A 70.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY

a.

Install the front engine service cover panel sub-assembly with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Install the shift wire clamp with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 33506F 71.INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

a.
A146457E04
0.667,0.073 0.781,0.219 0.115,0.146 10 true A 0.5,1.938 0.615,2.083 0.115,0.146 10 true A 2.781,1.74 2.896,1.885 0.115,0.146 10 true B 2.76,0.188 2.875,0.333 0.115,0.146 10 true B

Install the floor shift control shift lever retainer sub-assembly with the 4 bolts.

Torque:
for bolt A : 7.5 N*m (76 kgf*cm, 66 in.*lbf)
for bolt B : 12 N*m (122 kgf*cm, 9 ft.*lbf)


b.

Connect the shift and select transmission control cable and plate washer with the nut and 3 new clips.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 58123A 72.INSTALL SHIFT AND SELECT LEVER SUPPORT WITH BOOTS

a.

Install the shift and select lever support with boots with the 4 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Install the transmission cover mat.


c.

Install the shift lever knob sub-assembly.


Hide 73.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 74.CHECK INJECTOR COMPENSATION CODE

Hide 77.ADD POWER STEERING FLUID

Hide 83.BLEED AIR FROM POWER STEERING FLUID

Hide 84.INSPECT FOR POWER STEERING FLUID LEAK

Hide 85.INSPECT FOR EXHAUST GAS LEAK

Hide 53711C 87.INSTALL FRONT FENDER APRON RH

Hide 51445D 89.INSTALL ENGINE UNDER COVER BRACKET RH

Hide 51446C 90.INSTALL ENGINE UNDER COVER BRACKET LH

Hide 51441D 91.INSTALL NO. 1 ENGINE UNDER COVER

Hide 58420 92.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

a.
A399501C01
2.354,1.385 2.854,1.885 2.854,1.885 2.938,1.885 false 2.958,1.771 3.271,1.969 0.313,0.198 10 false *a
*a Knob


Attach the 2 guides and install the No. 2 engine service hole cover assembly, Turn the knob to attach the hook.


Hide 58734B 93.INSTALL REAR ENGINE SERVICE COVER WEATHERSTRIP

a.

Install the rear engine service cover weatherstrip.


Hide 58410 94.INSTALL ENGINE SERVICE HOLE COVER

a.

Attach the 2 guides, 2 hooks and install the engine service hole cover.


Hide 58521D 95.INSTALL ENGINE SERVICE HOLE COVER MAT

a.

Install the engine service hole cover mat.