Home › Engine / Hybrid System › N04C-VQ (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2019.08
RM2850E _51 Engine / Hybrid System _073144 N04C-VQ ENGINE MECHANICAL _0355904 ENGINE ASSEMBLY A

N04C-VQ ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.CHECK INJECTOR COMPENSATION CODE

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 58521D 3.REMOVE ENGINE SERVICE HOLE COVER MAT

a.
A399492

Remove the engine service hole cover mat.


Hide 58410 4.REMOVE ENGINE SERVICE HOLE COVER

a.
A399493

Detach the 2 hooks, 2 guides and remove the engine service hole cover.


Hide 58734B 5.REMOVE REAR ENGINE SERVICE COVER WEATHERSTRIP

a.
A399494

Remove the rear engine service cover weatherstrip.


Hide 58420 6.REMOVE NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

a.
A399495C01
2.292,1.354 2.615,1.604 2.615,1.604 2.771,1.604 true 2.802,1.49 3.115,1.688 0.313,0.198 10 true *a
*a Knob


Turn the knob to detach the hook, detach the 2 guides and remove the No. 2 engine service hole cover assembly.


Hide 58123A 7.REMOVE SHIFT AND SELECT LEVER SUPPORT WITH BOOTS

a.

Remove the shift lever knob sub-assembly.


b.

Remove the transmission cover mat.


c.
A399496

Remove the 4 bolts and remove the shift and select lever support with boots.


Hide 33506F 8.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

a.
A399497C01
0.458,1.063 0.563,1.063 0.563,1.063 0.771,0.854 true 0.281,0.99 0.458,1.198 0.177,0.208 10 false *1
*1 Plate Washer


Remove the nut, plate washer, 3 clips and disconnect the shift and select transmission control cable.


b.
A399498

Remove the 4 bolts and remove the floor shift control shift lever retainer sub-assembly.


Hide 58701A 9.REMOVE FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY

a.
A399499

Remove the nut and disconnect the shift wire clamp from the front engine service cover panel sub-assembly.


b.
A399500

Remove the 3 bolts and front engine service cover panel sub-assembly.


Hide 51441D 10.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51446C 11.REMOVE ENGINE UNDER COVER BRACKET LH

Hide 51445D 12.REMOVE ENGINE UNDER COVER BRACKET RH

Hide 53712C 13.REMOVE FRONT FENDER APRON LH

Hide 53711C 14.REMOVE FRONT FENDER APRON RH

Hide 17.DRAIN POWER STEERING FLUID

Hide 16400 18.REMOVE RADIATOR ASSEMBLY

Hide 17410 19.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 46700 20.REMOVE EXHAUST RETARDER ASSEMBLY

Hide 25608 21.REMOVE EGR COOLER SUB-ASSEMBLY

Hide 28100 22.REMOVE STARTER ASSEMBLY

Hide 44348A 23.DISCONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE

a.
C397492

Slide the clamp and disconnect the No. 1 oil reservoir to pump hose from the vane pump assembly.


Hide 44411 24.DISCONNECT PRESSURE FEED HOSE

a.

Remove the union bolt and disconnect the pressure feed hose from the vane pump assembly.


b.

Remove the gasket from the pressure feed hose.


Hide 27020 25.REMOVE GENERATOR ASSEMBLY

Hide 37140 26.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 45470 27.DISCONNECT TIE ROD ASSEMBLY LH

a.
A451484N01
2.469,0.396 2.302,0.396 2.302,0.396 1.844,0.688 false 2.5,0.302 2.865,0.469 0.365,0.167 10 true SST

Remove the cotter pin.


b.

Remove the nut.


c.

Using SST, disconnect the tie rod end assembly LH from the steering relay rod assembly.

SST
09628-62011  


Hide 45450 28.DISCONNECT STEERING RELAY ROD ASSEMBLY

a.
A451476C01
1.104,1.229 1.75,0.51 1.75,0.51 1.906,0.51 false 2.385,3.448 2.698,3.625 2.698,3.625 2.854,3.625 true 0.094,0.042 0.302,0.26 0.208,0.219 10 false *a 0.094,2.438 0.313,2.635 0.219,0.198 10 false *b 1.948,0.427 2.281,0.604 0.333,0.177 10 true SST 2.885,3.542 3.24,3.729 0.354,0.188 10 false SST
*a for Idler Arm Bracket Assembly Side
*b for Center Arm Bracket Assembly Side


Remove the 2 cotter pins.


b.

Remove the 2 nuts.


c.

Using SST, disconnect the steering relay rod assembly from the center arm bracket assembly and idler arm bracket assembly.

SST
09611-20015  


Hide 51202D 29.REMOVE FRONT LOWER SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
A449342

Remove the 6 bolts, 4 nuts, 4 washers and front lower suspension crossmember sub-assembly.

HINT:

While fixing the nut in place, loosen and remove the through bolt.



Hide 31210 31.REMOVE CLUTCH COVER ASSEMBLY

Hide 31250 32.REMOVE CLUTCH DISC ASSEMBLY

Hide 82121 33.DISCONNECT ENGINE WIRE

a.
A399647

Remove the 2 bolts and disconnect the engine wire from the No. 1 engine hanger.


b.
A399648C01
0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 0.094,2.406 0.406,2.604 0.313,0.198 10 false *b
*a LH Side
*b RH Side


Remove the 3 bolts and nut, and disconnect the engine wire from the engine assembly.


Hide 87246B 34.DISCONNECT OUTLET HEATER WATER HOSE B

a.
A146506

Slide the clamp and disconnect the outlet heater water hose B.


Hide 87245B 35.DISCONNECT INLET HEATER WATER HOSE B

a.
A146507

Slide the clamp and disconnect the inlet heater water hose B.


Hide 88320 37.DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

a.
A175430

Disconnect the connector.


b.

Remove the 4 bolts and disconnect the cooler compressor assembly.


Hide 44379A 38.REMOVE NO. 2 OIL RESERVOIR BRACKET

a.
C248665

Remove the 3 bolts and No. 2 oil reservoir bracket.


Hide 44774 39.DISCONNECT UNION TO CONNECTOR TUBE HOSE

a.
A260612

Slide the clamp and disconnect the union to connector tube hose.


Hide 23271F 40.DISCONNECT FUEL HOSE

a.
A260618

Slide the 2 clamps and disconnect the 2 fuel hoses.


Hide 11000 41.REMOVE ENGINE ASSEMBLY

a.

Using an engine lifter, support the engine assembly and height adjustments or plate lift attachments.

NOTICE:
·

Place the height adjustments or plate lift attachments so that the engine assembly is level.

·

As the engine assembly is very heavy, be sure to support it securely.




b.
A146473

Remove the 2 nuts and washer.


c.

Remove the 4 bolts and front No. 1 engine mounting bracket LH.


d.

Remove the engine mounting stabilizer and front engine mounting insulator.


e.
A146472

Remove the 2 nuts and washer.


f.

Remove the 4 bolts and front No. 1 engine mounting bracket RH.


g.

Remove the engine mounting stabilizer and front engine mounting insulator.


h.

Remove the engine assembly.

NOTICE:

When removing the engine assembly be careful not to damage any wire harnesses.



Hide 42.INSTALL ENGINE STAND

a.

Attach an engine sling device and hang the engine assembly with a chain block.

NOTICE:

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.



b.

Install the engine assembly to an engine stand with bolts.

CAUTION:

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.


NOTICE:

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.



c.

Remove the 2 bolts and generator bracket.


d.

Remove the 2 bolts and No. 1 engine hanger.


Hide 12180E 43.REMOVE OIL FILLER CAP ASSEMBLY

a.

Remove the oil filler cap sub-assembly.


Hide 12601B 44.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.

Remove the 2 bolts and No. 1 engine cover sub-assembly.


Hide 11202D 45.REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A446956

Remove the bolt and disconnect the 4 connectors and remove the wire harness.


b.
A446957

Disconnect the PCV hose and, remove the 6 bolts and oil separator assembly.


c.

Remove the 2 bolts, 2 cylinder head cover stay and 2 cylinder head cushion.


d.

Remove the No. 2 cylinder head cover sub-assembly and cylinder head cover gasket.


e.

Remove the 4 No. 2 cylinder head cover gaskets.


Hide 25620 46.REMOVE EGR VALVE ASSEMBLY

Hide 16577C 48.REMOVE RADIATOR PIPE

a.
A451527

Remove the 2 bolts and radiator pipe.


b.

Remove the O-ring.


Hide 44310 49.REMOVE VANE PUMP ASSEMBLY

a.
C401665

Remove the 2 bolts and remove the vane pump assembly.


b.

Remove the O-ring.


Hide 17201 50.REMOVE TURBOCHARGER SUB-ASSEMBLY

Hide 83420 51.REMOVE WATER TEMPERATURE SENDER GAUGE ASSEMBLY

Hide 11301K 52.REMOVE CRANKSHAFT POSITION SENSOR

Hide 11301M 53.REMOVE CAMSHAFT POSITION SENSOR

Hide 16630G 54.REMOVE IDLER PULLEY ASSEMBLY

a.
A146483

Remove the 2 bolts and idler pulley assembly.


Hide 88440B 55.REMOVE IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)

a.
A399656

Remove the 3 bolts and idle pulley assembly with bracket.


Hide 88431A 56.REMOVE NO. 2 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

a.
A403297

Remove the 5 bolts and No. 2 compressor mounting bracket.


Hide 88431 57.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

a.
A403293

Remove the 2 bolts and No. 1 compressor mounting bracket.


Hide 16331A 58.REMOVE THERMOSTAT

Hide 16333 59.REMOVE WATER OUTLET HOUSING

a.
A146582

Remove the 3 bolts and water outlet housing.


b.

Remove the gasket.


Hide 87208L 60.REMOVE WATER PIPE SUB-ASSEMBLY

a.
A449358

Remove the 3 bolts, water pipe sub-assembly and O-ring.


Hide 61.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A449359

Disconnect the 2 connectors.


b.

Slide the clamp and disconnect the water hose.


c.

Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly.


Hide 16206 62.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A449360

Remove the 8 bolts and water by-pass pipe sub-assembly.


b.

Remove the 2 gaskets and 3 O-rings.


Hide 16100 63.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 23741B 64.REMOVE INJECTION PIPE CLAMP

Hide 65.REMOVE INJECTION PIPE SUB-ASSEMBLY

Hide 23670 66.REMOVE INJECTOR ASSEMBLY

Hide 11177 67.REMOVE INJECTION NOZZLE SEAT GASKET

Hide 23811 68.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE

Hide 23810A 69.REMOVE COMMON RAIL ASSEMBLY

Hide 22100 70.REMOVE FUEL SUPPLY PUMP ASSEMBLY

Hide 71.REMOVE NO. 3 NOZZLE LEAKAGE PIPE SUB-ASSEMBLY

Hide 23300D 72.REMOVE DIESEL FUEL FILTER ASSEMBLY

Hide 23802E 73.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY

a.
A258070

Remove the 2 union bolts, the 3 gaskets and the No. 4 fuel pipe sub-assembly.


Hide 23803H 74.REMOVE FUEL RETURN PIPE SUB-ASSEMBLY

a.
A449343

Remove the union bolt, 2 gaskets and fuel return pipe sub-assembly.


Hide 23310 75.REMOVE UPPER FUEL FILTER BODY

a.
A257901

Remove the 2 bolts and upper fuel filter body.


Hide 19971E 76.REMOVE VACUUM PIPE

a.
A261715

Remove the nut and pipe clamp.


b.

Remove the union bolt, vacuum pipe and 2 gaskets.


Hide 29601B 77.REMOVE VACUUM PUMP OIL PIPE SUB-ASSEMBLY

a.
A399630

Remove the 3 union bolts and vacuum pump oil pipe sub-assembly and 3 gaskets.


Hide 29300 78.REMOVE VACUUM PUMP ASSEMBLY

a.
A399631

Remove the 2 nuts, vacuum pump assembly and O-ring.


Hide 23849G 79.REMOVE FUEL PIPE SUPPORT

a.

Remove the bolt and fuel pipe support.


Hide 23264D 80.REMOVE FUEL FILTER BRACKET

a.
A257904

Remove the 2 bolts and fuel filter bracket.


Hide 81.REMOVE OIL COOLER COVER SUB-ASSEMBLY

Hide 12204 82.REMOVE VENTILATION VALVE SUB-ASSEMBLY

a.
A449355

Slide the clamp and disconnect the hose.


b.

Remove the bolt and ventilation valve sub-assembly.


Hide 16206A 83.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A449356

Remove the 5 bolts and No. 2 water by-pass pipe sub-assembly.


b.

Remove the 3 O-rings.


Hide 17107 84.REMOVE EXHAUST MANIFOLD HEAT INSULATOR SUB-ASSEMBLY

Hide 17141 85.REMOVE EXHAUST MANIFOLD

Hide 17111 86.REMOVE INTAKE MANIFOLD

Hide 23809L 87.REMOVE FUEL PIPE SUPPORT SUB-ASSEMBLY

a.
A347517

Remove the 2 bolts and fuel pipe support sub-assembly.


Hide 23849G 88.REMOVE FUEL PIPE SUPPORT

a.
A257900

Remove the 2 bolts and fuel pipe support.